Search results for query: *

Not plastic for those years Metal

Honestly a flap disc on a die grinder is probably the safest hack way to enlarge the holes. Just go slow! Cley

I don't either, but lets be fair. I don't trust them at all on either side. They're all crooks. We just have to choose which we think is the lesser crook. Sad ain't it?

Are you happy with the power output now? If so, All I would do is put a crank kit in it. You don't bore one "just cause you want to", you bore it if it needs it. Does it smoke now? Use any oil now? Those compression numbers IMO are pretty good with a non stock cam. That tells me rings and valves...

Thanks everyone for their recommendations, thought about it over night and leaning towards: 1. Clay to determine hood clearance and decide what phenolic spacer might fit. 2. Installing fuel filter/Vapor separator used on 72-78 B bodies

Just so you know I tried putting those headrests on my non headrest seats and could not do it because the frame of the seat was different and did not have the holes to accept them and did not want to cut up my redone seats to do it so im just going to redo the seats with the headrests

My recommendation is this. FIND the steering column connector. Get familiar with RIGHT where it is. LEARN how to wiggle it back and forth and disconnect it QUICKLY. Once you have that mastered, the next time it starts acting crazy, get under there and unplug that connector fast. This will tell...

$20 shipped by media mail to your Zip

Bump

Squat proof??

Thanks

1967 Barracuda Passenger bucket seat rear seat track to floor pan outer reinforcement which is welded to inner rocker panels and the underside of floor pan

The caps were stacked inside the car when I bought it and after holding one up to the rim, I was surprised to see that there is virtually no lip of the rim visible at all around the edge of the cover, so the paint color on the rim is really moot from a styling perspective. Should have check that...

Now I back read.....

I figured I'd look at both options new and used

Just get a large Phillips screw driver and a propane touch. Heat up screw driver and just it thru from bottom to make perfect holes. No freying..

Do you have any under car pictures with the mounts as installed on the engine that you could post? How bad was the clearance with stock type steering box?

Or steam it...makes a nice install

:rofl::rofl:

Sounds good Frank , the only reason I use heat is to cauterize the hole so it does not fray.

Is the oil pressure good? Check with a gauge if You don't have one already. If it's a piston/pin it goes knocka-knocka & is a sharper/brighter sound, rods usually sound duller/heavier with a deep knock-knock. If that's Your ride in the avatar, I'd find & fix the knock, & get back to cruisin'...

What is your budget?

FWIW my horn staying on turned out to be melted wires at the bulkhead connector inside the car. The battery feed wire runs next to the horn wire and the battery feed wire started to melt and fused to it keeping the horn on. My fusible link went soon after and the problem was created at the ammeter.

So I put a pair of 275/60 15 M/T E.T. Street R’s on 10” rims. Formerly had 275/60 15 Cooper Cobra’s on 8” rims. Went out and did a couple of 1/8th mile pulls. Absolutely 0 spinning, with no burnout! Picked up .31 seconds from my previous best. Check out the Dragy. Can’t wait for my first...

Amazing times and speed with something you just put together and not broken in yet I see nothing but a fast future for you and I love the way the car is set up I have an F6 green demon and I love that color.....best of luck, Will

I remember this car being for sale a few years ago and questions being asked about all of the obvious deviations of the car. The one reply that I recall was that they liked the '68 marker lights so they were installed. May not be the same owner now putting it up for sale.

I bought an oil drain pan off ebay the other day and when I got here, the vent plug wad broken off (you know the kind, rhey come on the good Jerry cans aswell) No big deal, I figured I'd give the seller a chance to make it right I figured, send me a new plug or a few bucks to buy one, and I...