Search results for query: *

I agree they are bending the rules as the shop is not a dwelling. The requirements for the driveway should have been addressed by the fire dept in the pre approval. I'm curious how you got an approved permit without this addressed .

What are the requirements in the municipal code? Has your permit been approved?

Meh.... I've jumped a 2016 ram 2500 crew cab with wheel spacers on the front end and then put 40,000 miles on afterwards. Zero problems but i did retorqe and add loctite per the instructions, seems that any failure I read about on the interwebs there is always something questionable about...

73 duster slant six. I can't decide which way to go for a motor swap. I have a 318 block I could 390 stroke, find a 360 which seems to run 600-1000 for a stock engine with questionable past, or I can buy 440 motorhome engines usually with trans and low miles for $500 all day long. Anything I buy...

I think 73 was a one year only setup, I have a piece still out of my 73 and will provide a picture later when I get home

The gasket has an extra flap at the bottom of the windshield making it impossible to install the trim, is this supposed to be there? 73 duster

No I didn't know that. Used two paint sticks and a screwdriver.

Front glass installed today, that front lock strip ain't no joke! Of course to get the glass in I had to have fun with the wiper linkages and reinstall the dash.

A little cleaning and beating the trim on with a hammer and paint stick, new trim clips are beefy and didn't want to play nice. Still have to reclean the glass

I'll check that out

Yes wtf indeed First 10 minutes I was really second guessing my life choices having never done this. Luckily paint thinner takes that crap right off.

I have a clear filter before the carb, and the gas siphons back once the car is turned off. It will run off the bowl, then stall. Usually have to crank for a while, id say up to 20 seconds before getting fuel back to the carb. Not sure if the capped purge on the canister is causing this or a...

First time installing glass

It's not letting the bowl, it's emptying the fuel line, sorry bout that. As you can see the purge line is capped off.

Skid steer or mini excavator around town. Used to tow a 30ft travel trailer on longer trips.

73 duster 225, one line runs to carb vent, Holley 1920, one to tank vent, and the purge line is capped off. Where is the purge line supposed to go? Manifold vacuum? Teed into the ported manifold line running to the distributor? The factory emissions controls has been deleted by me but I bought...

Got an 18 2500 Cummins on 35s, gets 14 city, 18-20 highway, depending on load 8-13 towing. She won't win any drag races or sip fuel, but towing is a dream. Really need to delete the truck. Had a 16 2500 6.4 , also on 35s, was more sporty than the Cummins but went through two brand new engines in...

Did you check the rear brakes for broken parts? I've had this happen before, it was a broken spring in the rear drum

So the 600 is really working well to smooth it out and overall I think I'm in better shape than I thought. I do have some sand through on edges and a couple thing spots but I think if I hit the thin spots with primer, a touch up gun, resand, and apply 2-3 more coats I should be good. I really...

Yes there are spots with not enough coverage and spots where I try to wet sand the rough texture and get down to the primer. I still have a gallon of the single stage left as I bought two gallons because I knew I would probably need extra.

I painted my duster with summit single stage performance yellow paint and have many areas of thin paint and lots of orange peel. I am NOT a painter lol. I was wondering if I can spot repair the paint, sand it smooth, and clear coat it? Basically treating the yellow like a base coat that I can...

Arrows point to the trim clip holes. The area in question is circled, was/is filled with lead and or factory seam sealer but was curious if that's supposed to drain.

Are these spots supposed to be open?

Anybody purchased the oer snorkel scoop, how's the quality? Any other brands worth considering other than OEM?

How To Measure V Belts Correctly - Determine My V Belt Size.

Dan you'd probably be happy with a sweet sounding dual exhaust and a properly running bone stock engine. After that I'd do rear gears to 3.55, then engine and torque converter

I went through two hf purple guns yesterday that I bought last year. Both of them the trigger was catching that got so bad that they wouldn't even work.

In 10 pages we'll be talking about either a blown methanol powered 318 with a 500 shot of nitrous or buying a stock 360 lol.

16 and 18, my wife is on there too so 4 drivers total