Search results for query: *

Even if I go with a lower profile? Say 255/55 or 255/50 ?

No one else ? =)

Had any problems with tires rubbing in bumps with those 255 ? Hm, yeah I guess, it seems that there's plenty of room going in but much less on the outside though that's what I expected, it would be interesting to know if anyone has squeezed in anything even bigger without mods, Offset on the rim...

Well there's problems with all of those, neither the tti's or dougs can handle column shift, harold is impossible to get ahold of and even if I did there seems to be some issues with getting anything anyway. and the 273 and 318 manifolds is quite ridiculous for a 392 stroker. Well, **** happens...

Thought so to... Any way to massage them to fit in an early a?

Anyone know what headers these are? Supposed to fit the early-a http://www.blocket.se/halland/Hedders_forgasare_valiant_dart_mm_34364348.htm?ca=1_9&w=3

Hi! I want to get me some new 15" wheels to replace my stock 14", however I would like to get as wide a tire and wheel as possible without minitubbing, so now to the questions - What's the maximum possible tire diameter - How wide can I go and still keep within the fenders? - What's the...

Is there really no-one who can answer? How wide a tire can you run on a '66 and what offset is needed for it to be possible?

Sorry but need both of them =/

Hi! I just talked to the tech support over at Dougs and they claim that their 63-66 Early-A non-fenderwell headers will work with a power steering and column-shift car, is this correct?

Hi I'm looking for the innerfenders/splash shields for my '66, that's the parts that supposed to keep water from the door and headlights Contact via thread or pm Best Regards!

I have found a wheel with the following data 15x8" 4,625 backspacing +3mm Offset Will these fit back on my '66 Dart 4-door, 8,75 rear and stock springs and wheelhouses? What size tires to use if they do fit? How big diameter to aim for to keep em from rubbing and how wide? I'd like as...

New, used, no matter... I'll take 'em if you're not crazy on the price Contact via PM and my e-mail : [email protected]

Thought it mightbe something like that ;) anyone know what thread it is on these lines? :)

If they're left I'll take 'em right away. Pm me

Haha I did notice that after alot of irritation, never seen the rotor behind the hub on a car before! Problem solved! But now I have a new question! There are three brake-line holes in the KH calipers but I only have the one brake line on each side from the drums, what to do?

sorry for worthless spelling, i was writing on my phone with to big thumbs...

Hi all! I bought a small bolt kelsey hayes brake kit to convrt my 66 dart tp front discs and the kit included stock 67 spindles and ϧcontrol arm and hub but when i mounted the spindle, bearings and hub and tried to put the rotor on the hub i noticed two things, one is that tthe rotor hits...

I lifted the engine out of the '66 Dart today and noticed that almost all the rubber bushings is in quite a bad condition and almost falling to pieces resulting quite some slack in the steering, does anyone offer a complete set of steering bushings for these cars? Who and what to buy?

Need the coupler between the steering gear and steering shaft rether I had it yeasterday. Please sen PM if you have one for sale.

I've found the followinf casting number inside the distributor, does this help? 2875032-05102-4

Hi! I've heard and read (on this site among other sources) that the stock rockerarm ratios is quite alot under the 1,5 they're supposed to be, but both mopar performance and sealed power makes stocklooking rockerarms for the small-block chrysler, the question is - are these true 1,5 ratio or...

Can anyone confirm those ebay valves that they do fit and are of good quality? Where to buy ferrea valves then? =)

Hi all! I'm looking at buying some RHS bare heads and want to get ahold of some ok valves at a reasonable price, want 1,625 exh ant 2,02 int valves, found some mopar perf valves but it seems to me that they are quite expensive at around 400 Usd for 16 valves, so my question is if someone has a...

That's kind of the problem, I'm away in Norway for work right now and can't really check up on it either and anyways it's hard to know since i haven't checked the engine block for the numbers and it might as well be that the ignition has been changed some time, don't actually know! How many...

Hi all! I'm looking for a new vacuum advance unit to replace my broken one in my Dart, the engine in the car is a LA318 and it's a mechanical distributor with a single breaker point, what I need to know is what is the partnr for the vacuum advance and where can I find one? Oh, and by the...

Well, I have gotten a few things done since last time! A 392 stroker has been built, the 904 completely restored and improved some, changed to front disc brakes and power steering, painted the hood the same colour as the rest of the car and bought a set of stock rallye wheel and painted them...

Yeah quite, there's no power steering or anything else that could possibly leak by revving under the hood

pcv beeing? But i does have breathers on the valvecovers, what could be the reason for this excessive pressure then? To my knowledge and my friends all parts are stock but then again we might both be wrong, oilfilter is a new mann filter checked the dipstick and there's no oilpressure meter

Hi all! i have a strange problem in a friends car, it's a '68 Dart with a 318 of unknown origins and a 904, what happens is that when revving the engine high for example when burning tires there suddenly comes a great cloud of smoke from the engine compartment and when one opens the hood the...