Search results for query: *

You want the holes to be in front of the crook of the air dam in the bottom of the scoop. I'd take out the studs first and move the scoops around the hood and see what looks best, You wouldn't want to place the scoops so the hole in the hood compromised the hood frame, so that will limit your...

I am trying to wrap my head around this... what you are saying is that when you install the non-adjustable axle, without the adjustable axle in place, there is no play when you tighten the 5 nut flange? Are you sure that the bearing race is seating in the housing? Have you tried swapping sides...

Are you taking a car to Carlisle - if so post a picture

mis adjusted wire from driver to passenger track...

Mancini Racing had the Mopar Performance version. I would advise calling them to get straight answers, their web site sux

Welcome to FABO!!! So, Does it have TA heads?

What are you putting the scoops on - what hood? The 1970 340 Darts all had scoops with holes in the hood. I don't think any of the Dusters that used these scoops came with holes from the factory. Installing the scoops and cutting the holes is a piece of cake on 70-72 Dart hoods because of...

Can somebody find the video by a member here talking about the various ways to replace the bushing with the least pain?!!?!?

just curious, when folks use a small port manifold on big port heads which intake gaskets do you use???

OP - So that you understand the thrust button and adjusting the axles better. Stand at either the yoke end or ring gear end of the drop out. Stick 2 long tools in each side of the dropout to contact the thrust buttons. You should be able to press lightly on the tools and feel the thrust...

I tried to send a pm, but your box is full. I'm going to Carlisle AND to Moparfest and would be willing to talk to you about transporting new armrests from one to the other, if that helps...

Pictures!!!!We Demand Pictures!!! :mob::mob::mob::mob: :lol:

So back to axle adjustment... What kind of bearings are on the axles??? Green bearings are a sealed bearing set and tapered roller bearing (original) have a set of tapered roller bearings and a race. Post a picture of the axle bearings on the axle if this is greek to you. Green bearings are...

OK, I just gotta ask - what does a spare tire elevator do???

sell the locals a first right of refusal. Then you can look for a buyer and if you get a legal offer from a legitimate buyer, the locals get to buy at that price if they want it. We buy such rights in conservation work all the time.

Does your trans have some sort of shift kit installed? If not I would recommend one. Or better yet when you contact A&A you could get one of their valve bodies and just replace yours according to their directions. you don't even have to take the trans out - it all just happens through the pan...

get yourself an infrared heat sensing gun (I got a cheap one at Harbor Freight that works just fine). You can check the temp at the thermostat housing by the temp gauge sensor at start up through fully warmed up and you can figure out actual temps at various gauge readings. It might be that...

If you are puttering around at 30mph and kick it does it drop into first???

I would not let that stop you. The bad guy in my story was supposedly a friend and there was no contract there either. The lawyer will let you know if there is no case.

let us know if that fixes it. If you can stick with the LD-4B...

When you drop in the right gaskets the clouds will part and a shaft of sunlight will fall directly on your engine (cue fanfare an angel choir in background) and I will bet all your problems will go away (at least having to to with this engine). From the sounds of the engine I bet it turns out to...

With $70,000 into the project, I'd be looking for a lawyer and a legit shop to look at the car and assess it. A friend of mine got screwed on a car issue several years ago. He got a lawyer and ended up suing the guy and ended up with a judgement for $30,000 plus interest until the debt was...

Those are 340/360 gaskets, the holes and the sealer should be a lot closer to the actual ports. Big port vs small port factory heads...

What color would you prefer??? No sense changing color if you can get the right one!

For earlier intakes you can buy a replacement housing (straight up style) from NAPA and it comes in cast iron instead of aluminum which is much less prone to warping.

I ran across these new taillight lenses on ebay motors for less than $80 delivered https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2499334.m570.l1313&_nkw=1970+Dodge+Dart&_sacat=6028

OP: re the first photo in your first post. Every rallye wheel produced by Chrysler has this inner and outer ring mounting arrangement. Its been working fine since 1970...

no check valve. You seem to have a vent system that is older than your car. up through 1970 the vent was simple and ended inside the rear frame rail. it is actually design not to vent anything out of the tank, but rather let air into the tank to balance the fuel being pumped out. 1970 CA cars...