I get my bulbs from superbrightleds.com but others have them too. Select the location of the bulb you want and you can choose the color.
https://www.superbrightleds.com/vehicle?find=1968-dodge-dart-6765916&sid=On5qXZAD8B
I had my engine built in the South Texas/Bergheim area and there is a guy that is a mobile HVAC tech that comes to the house that makes custom fit hoses. There might be someone like that near you.
I bought a set of remflex gaskets to use for reattaching my headers after my rebuild. As I was putting them on the header shifted and the gasket slid down and bent... ruining them (yeah, both sides). Very frustrating waste of money.
I do have a set of stock manifold gaskets and am wondering if...
One thing I do love about working on a van is the engine is right there after the doghouse is removed. With the weight of the van and the rear gearing we had to put a stiffer spring in to keep the 600 carb from bogging. The stock silver spring was too weak, so think we went to the brown. Good stuff!
If you have a saginaw power steering pump you can get the shim kit from BergmanAutoCraft.
https://bergmanautocraft.com/product/shim-kit-saginaw-power-steering/
Got an email back from the tech at Harland Sharp. He recommends .015-.018 clearance cold that I could achieve by mixing/matching the thin spacers to achieve. I understand 440 Source recommends .015-.030 for a similar rocker.
I am using Harland Sharp roller rockers on my 440. The instructions say to have a side clearance per cylinder from between .008 to .012. I recently took my engine apart to deal with other issues and am now reassembling things. I noticed some of the rockers and .047 spacers show interference wear...
I was looking at the Progression Ignition distributor for my 440 engine. The question that concerned me was how it would fit. I am using the Trickflow 240 heads and Ansen cast aluminum valve covers. Well, I pulled the trigger and got the PI distributor and can say it does fit without modifying...
"Cranks like a dead battery drops to 6-8v and is very slow to crank and does not start." Voltage drop like that still points to bad connections. You changed the starters, same issue. You tried a jumpbox up front but where did you attach the cables to? Directly to the starter & bellhousing?
Sounds like a classic case of bad connections. Did you make the terminal ends of the wires going from the battery to the engine compartment? Did you have someone do a load test on the battery? I would temporarily put the battery at the front and wire directly to the starter & relay with OE style...
I got the covers from Ansen, but they are currently sold out of the black/finned finish. Think they still have the polished ones though. I would not get any different covers unless you have a baffle/splash problem... or you just want to change the covers...
Yeah, mine did too, but they were inadequate! Just a heads up. After you install the PCV and run the car, pull the PCV hose from the carb and look to see if you have any oil in the hose. Before I changed the covers I had quite a bit!
Be sure to look at the quality of the baffling under your valve cover. I had a set of M/T's that did little to nothing to stop oil being ingested by the PCV. I changed to another company's cast covers and it made a day & night difference. Just a heads up, but your issue sure sounds like the...
Best not to mix and match like that. The Wagner unit will do a great job at keeping vacuum in the engine at all but WOT. Since no one runs WOT all the time, you are really dealing with idle & mid throttle issues with the PCV.
You may want to look into the ME Wagner Dual Flow PCV that can be adjusted based on what your engine needs. Would be a lot simpler than going to a vac system.
https://mewagner.com/
I recall a Nick's Garage episode where he said the biggest issue he's seen with these leaks is when the block was line bored. Was your block line bored?
Funny, years ago people would buy the B&M Trickshift fluid. It was mostly rebranded type F! The 727 & 904's are not picky about the type of fluid. I've run type F for decades without problems. Like others have said, run what they recommend.