Search results for query: *

Still available, price dropped to $265 shipped in the US.

replied to PM

Price reduced to $290 shipped anywhere in the lower 48 states

Do you happen to still have this fan and clutch?

Price reduced to $300 shipped anywhere in the lower 48 states.

Very nice, like new Edelbrock Torker 383 Intake for sale. I bought it for my wife's big block build but we ended up going with a trick flow intake. Will work with any low deck big block mopar. Located in Nashville, TN 37218. Asking $325 shipped to any of the lower 48 states.

I promise he would help if he had thumbs. He wants to help sooo bad!

I am selling a good running 383/727 that was just pulled out of my wife’s 68 Chrysler Newport. The car ran great when pulled out Saturday 10/01/2022. We are replacing this with a sporty 512 Big Block so I am keeping the distributor and front accessories/pulleys. Other than that, this engine is...

Of course! I'm addicted. We plan to Rocky Mountain Race Week 1.0 next June and Dragweek 2023. We are building my wife a car to drag n drive also. 1968 Chrysler Cordova 2 door. Don't ask me why she wants to race a boat. Building a 512 big block for it. She doesn't want a cage so just...

My torque converter went out a week before we had to leave for Dragweek 2022. Sent it off and had it rebuilt. Let's just say the car hated the torque converter. It was waaaay too tight. The last few years this car has run consistent 10.00s with 10 lbs of boost. At test and tune on Sunday in...

Cool car buddy, can't wait to see it in person

904. Lenny at Ultimate built the converter for this car in 2018 so I suppose it's time for a freshen up anyway. Does anybody know if he still owns Ultimate? Last time I called them I couldn't get in touch with Lenny.

I think I figured it out. Went for a drive. At a stop sign I foot braked the car it would only stall to about 1,900. Floored it and it was a total dog, didn’t even spin the tires until we hit about 3,000 rpm. Torque converter is shot. Probably needs freshened up

Thanks for the reply. I don’t think it’s a timing issue because this car has always liked 20 degrees of initial timing. Thanks for the tip on the idle adjustment and I’ll try the eraser trick. Maybe those metering block gaskets do need replaced.

No, I’ve got a fuel pressure gauge on the cowl and an air fuel gauge. Pressure is normal and air fuel ratios are in line. Thanks for all the ideas though. This is what I was looking for.

I verified timing becuase it almost acts like one that doesn't have enough initial timing when you put it into gear.

Yes, I did verify 20 degrees locked timing the same day I did the vacuum gauge. Yes, I'm curious about a vacuum leak as well.

I've got a 71 Dart Street/Strip car with a 414 C.I. stroker and a procharger with a Holley HP converted to blow through carb. Been running this set up since 2019 with great results and doing dragweek a lot. The timing is locked at 20 degrees. Typically this setup idles great in park at 900...

I am signed up for dragweek 2022 but since they switched all the tracks around I'm not quite as excited about it. I've been to all the tracks they are now going to. Contemplating doing Rocky Mountain Race Week 2.0 instead. Not sure yet, I'll keep you guys posted with what I decide.

as you can see it's tight and the stock door pull hits the diagonal door bar.

I was able to squeeze my 6 point roll bar in with factory front and back seats and also kept the stock door pulls. Not sure if this helps.

I also wouldn't over think the torsion bars. I'm still running the stock 318 bars that came in the car.

Obviously, you are getting a lot of opinions, but I'll let you know what I do with my Dart that runs 9.90s in the 1/4. I run SS springs (add a clamp to front segment, remove rear) I run 4 degrees negative pinion angle make sure your rear shocks are long enough to let the SS springs do their...

Here is a video of my pass in Gainesville. I'm just starting to figure out my youtube chanel. Started it for my music and now I'm going to start adding drag racing content.

Foreign music? There are 6 country songs on my Youtube chanel. I'm going to start uploading some drag racing videos as well.

I would like to go but only have 79 subs on my music youtube chanel. Cody Walker Music - YouTube Would be bringing my 71 Dart

So... I have been asked to attend the nonamenationals and would like to but my Youtube chanel only has 79 subscribers. I have more than 800 followers on Instagram, does that count? Cody Walker Music - YouTube I would be bringing my 71 Dart.

Monday went 9.94 first pass, too quick can’t turn in. Had a fuel delivery issue 2nd pass so I lifted real early and coasted to 10.88. Anded weight, short shifted and lifted on third pass trying not to break out but air had gotten better and it went 9.94 again . had to turn in the 10.88 so kind...

If any of you have Instagram you can follow my journey @codywakermusic

Monday went 9.94 first pass, too quick can’t turn in. Had a fuel delivery issue 2nd pass so I lifted real early and coasted to 10.88. Anded weight, short shifted and lifted on third pass trying not to break out but air had gotten better and it went 9.94 again . had to turn in the 10.88 so kind...