Search results for query: timing chain

...hard to see. No more than a balancer costs, I would replace it vs doing a repair sleeve. I suspect that you are probably replacing the timing chain too if it is sloppy. All of this can be a bit daunting if you haven't done it a lot, so hang in there...

Oil pan sold. If anyone’s interested in the crank and timing chain cover I’ll do $50 for both local pick up. Thanks

...all back together though and cold starts and throttle response seem to be much better. and it seems my timing jumping around was in the timing chain slack because it's gone now with the new 440 source chain. i plan to get it out tomorrow and see how it drives! i also got some new 275s for the...

Well, the oil.pump and pick up are working or you wouldn't have oil pressure. The intake doesn't have oil running through it so that's not an issue.

I couldn’t tell you about the starter since I’ve only ever run mini starters on mine. As for the oil pan, you can run either timing chain cover with either oil pan, but if you are using an la oil pan, it needs to be a 360 pan (which you already have)

I get it works ok. So does no holes in any bolts. Or no drip tray. Ok isn’t good enough when I have to stand behind it. Drilling a hole in a bolt isn’t any harder than drilling a hole in the plate. And it’s not just for gear drives or Chrysler stuff. I put pressurized oil on Chevy’s too...

What side of the chain do those tensioners work on? If the "downwind"(following) side it will pull the cam timing "retarded" and will retard cam timing worse than if the chain slip was allowed to "float". Though it will hold it more consistent and not "bounce"as the chain does wear. I have a...

...have 2° advance ground into them. Then the unknown, the degree of advance or retard added upon assembly. Then also miss match of timing chain parts and gears giving an unexpected advance degree setting, throwing the formula off hence the picture at TDC. See what others think.... ☆☆☆☆☆

...you what to do with your engine, it's YOUR engine... That's what I do with mine... And yes, there are very few of the original timing chains left, but if I have an engine with one - it's getting replaced with a double roller ASAP!!! The increase in MPG will pay for the chain soon enough...

the slinger keeps oil off seal, also, slings oil around timing chain, only oiling it gets, i've ran with out one once, chain had lots of stretch and wear. just food for thought

The timing chain set looks to be an aftermarket one. I don't see any significant slack in the chain, so, if it's a good quality set, I'd reuse it. How many miles are on it?

...with timing, you can check the timing on the starter. This will tell you that the dist is working and timed as well as that the timing chain is in time. Yet another thing, if wiring is a ?, is to simply jumper a lead from the battery to the coil +. Do not leave that there any longer...

You are right about the timing chain. The S-402 mark is from a Comp cams 2103 set...I am not sure about how many miles.

first, check make sure balancer ant slipped and top dead center is true!, 2nd check timing chain gears are marked correct, theres a bunch of timing chains out there thats marked wrong! friend had a new chain on a chevy last week that was marked a 1/4 turn of the crank off! if it runs 180 off...

That’s why you degree the cam with the tensioner on.

method as specified in a chrysler Australia tech bulletin for Hemi 265 https://www.geocities.ws/drhemi.geo/camfloat.html I didn't bother with the screw. too much hassle. things have moved on since 1976. I used a 3 bolt cam, machined a Nylon? big block cam button and stuck it in the...

They make a collar you can put on the distributor shaft that will minimize any upward motion the drive gear might have. After that’s installed, if you still have the timing mark jumping around, it’s likely the loose chain. They’re often not rock steady on a BB, so how much it jumps around and...

Evidently so. It quit running and doesn't operate the rockers or turn the distributor. He said he thinks it's the timing chain. Read the previous page. Stan, you'll get it, buddy. That's what it's all about!

Oldmanmopar... Thanks! I'm going to look at this pan on Wednesday. I can't take the motor, but I will take the timing chain cover and fit it. I worked part time at an auto shop that did a lot of Stock/Super Stock front ends. And a few of the stocker guys started using Dakota pans and pick-ups...

...shelf, sent them to the machine shop, new valve job, slight surface cut for flatness. Put it together with new bearings, oil pump, cam, timing chain, studded the heads, and added a windage tray. It ended up with 7.5 measured compression. I have less than $1000 in the whole engine, not...

I disassembled my slant timing cover few months ago. Today at last got time to install new chain and sprochets, gasket, seal, damper, radiator. After everything in place I noticed this damn slinger in the table. This happens when there is much time between disassembly and assembly.. didnot...

Timing chain ?

Hi Guys, is the stock timing chain cover sufficient / strong enough when a roller cam is used? I plan to use a hydraulic roller in a 512, have got the comp cams 206 cam button to ride on the cover. Small block guy doing this swap the first time, so any information is appreciated. Thanks! Michael

yes double pumper. and a/f gets a little lean at wot but not anything crazy. it's around in the like 13s. having slack in the new timing chain i put on makes me suspect. any recommendations on a good timing set to buy that should install with minimal slack? would a gear drive be more precise...

...in little by little hopefully some more progress in the next couple of weeks. Basically, short block is together. Crank, rods and pistons. Went to degree in camshaft and the timing chain gear set was mis-boxed. Correct part number incorrect parts. I should be postings some more pictures next...

I would add new core plugs, timing chain, and head gaskets in addition to cam bearings to any used engine as well.

Well of course it's gone. You tightened the bolt down. You better believe it though when it's running, that cam sprocket will probably rock back and forth. That crap wouldn't be in any engine I built. Rock on, brother!

New never used timing chain set . 3103 $50. + shipping

If it was any tighter, I could not install it and that's with aligned hone and decking. Mopars rock!!!