Search results for query: *

Absolute B/S.....I agree. I used to patronize a parts supplier exclusively without shopping since I had an account with them. On one occasion, they didn't have the part I needed so I tried one of their competition to see if it was in stock. They were $100 cheaper right off the street for the...

It would be an improvement. Of course that’s exactly what a W5 head is except it uses an offset rocker. Chrysler didn’t use an offset rocker for no reason.

Yeah, Reversion Raceworks! Good guys to work with.

I just put Bilsteins on the Ford and have them on the Nissan. Also have KYBs on the Valiant :lol: I'm sideways with all parties involved

I don’t know much about any of this stuff but I’m gonna say it out loud anyways. What if you raised (taller) the head with taller runners and use stock rocker location and make new intakes

Need to figure out my alternator/ charging issue on my pull truck. And find some 6” rear leaf springs. Right now it’s got that Carolina squat.

Kind of hypocritical

Bought front rotors for the Wife's AWD Challenger GT last week. Napa and Carquest where $249 and $279 Cdn respectively EACH. I bought the SAME rotors at Partssource (and they had stock vs having to wait 11 days that NAPA was going to be) for $109 each! I've always avoided PartSource.. aka...

Wow, I'm looking to get Bilsteins for my Duster and it won't be stock height but I'm not getting into that one and asking any questions, geeze!

Your the story teller

What they really need is a Hellcat swap.:lol::lol:

All cleaned up for cry baby.

True! But it's a eye opener to see a pull with the correction factor just under 1 percent, and then it reset to 10% for the "hero" pull

That is all true. But there is no demand for other alternatives. Mopar LA stuff is a limited hangout, and many that have that stuff are uniquely to Mopar..cheap. That said, not many( I have seen) 9 sec n/a pump gas Chevy/ Ford small block cars driving around all over. Considering there are no...

I will take it sending pm

1970 Dodge Dart Swinger two door Slant 6 225 paired with a three-speed automatic transmission, Vinyl Top gone and rusted out. California car with lots of rust. Vehicle currently registered to 3/2025. Runs and drives tight and smooth going forward but tranny may need rebuild as reverse no longer...

Thanks , found out it is a 67 with 68 marker lights added. It does have the knob radio.

Moderators can you come on here and clean this BS up

Seat Number 2 done. This one didn't come out as clean as the passenger side one, the covers were pretty stretched out and tired. And a good bit dirtier. They will pass for a season though until i can afford new foam and 70 duster specific covers from legendary.

The problem with putting it on jack stands is, it likely will no longer make the noise, because the weight is off the tires. The weight really needs to be on the tires to really duplicate properly.

Looking for single groove fan pulley part 3462825 and or 3671219

Thanks Rusty. I will do exactly that (I think I have a 24 inch piece of rebar that I can use as the poor man's "stethoscope"). I wish I had a lift but maybe I can just get the whole front up on jack stands.

Too bad. Do you have info for the company?

FTFY ;D

some of us do more than just drive to the ice cream stand. also, a list of the items adjacent to you in the shop does nothing to shore up your bonafides. your displeasure with the experience you had is noted, but don't push the narrative that the shocks aren't a viable upgrade for others...

Horrible logic.

Looks like the car show at the casino I missed out on… stupid job that pays for my Dart’s needs lol. They usually have a decent sized turnout there

No, but didn’t ask either.

Ok. Then here's how to find it. You can do it on the ground but it would be easier on a lift like a drive on or an alignment rack. Get a LONG 3/8 drive extension and with someone in the car duplicating the noise, place the end of the extension on each ball joint and put the other end against...

Corrections for atmospheric conditions are a necessary evil for dyno testing comparisons.