Search results for query: *

how much can you bore out a 360 block? its .030 over now, but has some scratches on a few of the cylinders that I can catch my finger nail on. it appears to be a 1973 block .

Im installing a new cam in my 360 block,I didn't take the motor apart so I need some help.Beside the cam retaining plate is there suppose to be a washer behind the cam drive gear? It seems to me that the cam moves to far forward making the cam lobes not line up on center of the lifters. This is...

I would like to sell it all as a complete kit oil pump lines pick up and repair kit 175 that’s a killer deal

old but good condition

magnafuel 500 pump 175.00 holley 1050 angular discharge carb w/adj air bleeds 300.00 mopar bb flex plate 25.00 csr smblk waterpump 150.00 bblk ati harmonic balancer w/bolt 125.00 bblk milodon oilpump and dual pickup & lines plus rebuild kit 175.00 bblk b&m flex plate 75.00 barry grant...

Need 72 dart driver side front windshield verticle chrome molding.

Have a cast iron intake manifold , inside the manifold in the runners there is dark brown coloration, I assume that this is rust because the manifold has been sitting for some time. My question is how to get the surface rust out of the runners? Thanks in advance.

What position do the rocker shaft oil holes for the rocker arms face? Face up or face down?

Used but in great condition

OK how do you clear inbox.I’m just outside of Chicago

What other information would you like to know?

I am in me illinois pics tomorrow

Mopar mega block 4.505 bore, pn 2468330-m. program main caps ,lifter bores bushed and indexed, deck o-ringed, billet main seal cap. $2800.obo

I am priming my 340 , have 60 psi on gauge but no oil bleeding off the rocker shafts,what am I doing wrong? The passenger side rocker shaft is off the head while priming motor.

need some information on a problem I have, was driving my dart just cruzin along oil pressure was 60 psi , then for some reason it dropped to 20 psi while driving same rpm. Got home did a quick assessment of situation notice very little oil lin price valve cover. Pulled distributor, spun oil...

Spld

sold

FBS cylinder heads cnc'ed titanium valves,single intake ,intake spacer ,valve covers ,offset lifters, t&d rockers. Made 949 on hp with nos cam 540cid. $5000 (Price made legible by moderator)

Anyone have experience with eagle or K1 rotating assembly's? Which is better? Pros and cons opinions, need to be able to tolerate about 550 to 600 hp. Much thanks

I bought cnc"ed 468 on intake 330 on exhaust. It could of made more power,but I had a nitrous cam in it.

I checked rock auto they don't have nothing listed under horn relay they just have a general relay,but it only has three pins mine has four. I believe it's a combo for the door open buzzer and the horn that I have

WTB horn relay for 72 dart. Also need 36 tooth speedo gear for a833 4 speed

I have a set of Fred brewer heads I ran years ago. Made 949 hp I n dyno. 540 cid ,one carb.

Can use some help on how to set pre load on 340 with hydraulic roller cam and roller rockers,

. Trying to put in my 4 speed tranny, but I'm about 5/8 of a inch from bolting up to the bell housing and tranny won't go in any further. I installed a new pilot bushing into the back of the crank. I installed the bushing flush with back of the crank flange. My question is this the right...

I have 72 dart, when I press the horn on the steering wheel the horn does not sound.When I apply 12v to horn On bench they work.My question is there a horn relay somewhere that I am missing. the wire is connected to the steering wheel .

ok thanks , dissasembled the car last fall, thought that there was a piece there.

Interior trim piece that goes on the top of the front windshield that covers up where headliner meets the windshield for 72 dart

have a question on how to remove burnt oil from header tubes without removing the coating, any recommendations welcome.

Yes that what was explained to me to do.Was not sure if that pin would come out. new bearing in now problem solved