Search results for query: *

I have a 72 dart setup identical to what you are talking about, dana 60 moved back 1.25, caltrac setup with sliders etc. I drive it a ton on the street and a fair amount on the freeway and I can say I think it drives better than it did with all the stock stuff. Is your car painted green go...

That is a valve notch from the factory.

last time I needed a single ring I called total seal, they will get you what you need, not super cheap but it will be correct, if you do call ask for August, he's a mopar guy.

Nice!, if I had the time to do it I would just follow through on our dyno but time equals money and I am short on both lol. It would be awesome to compare his dyno results to ours though, what an interesting bunch of info that would be!.

@NC Engine Builder I wish you were not so far away, Tim and I would jump in and help out. I have been planning for this same test for a while now and would only be missing the bloomer heads at this point. I have literally every other head you mentioned and more including a fresh 410 short block...

A lot depends on the type of clutch you are running, if you don't have an adjustable one than check out the clutch tamer @weedburner . I went with a dana 60 @Newbomb Turk s advice since he figured I would be stepping up the power levels later and it turned out to be sooner so he was right.

I haven't met him yet, I wonder if this guy is the wife's boyfriend he is always talking about, as long as the guy ain't messing with the dyno :lol:

Who is this guy pretending to be @Newbomb Turk and what has he done with the real Tim?

To the op I would set the compression around 10.5 and put a solid flat tappet cam in (something close to these two) and run it. HUG STL4246AS-8 SB SLD FLAT TAPPET CAM 242/246 -108ºLSA HUG STL4650AS-8 SB SLD FLAT TAPPET CAM 246/250 -108ºLSA Even if it falls 15-20 short of your goal it...

Don't forget you have a ported tunnel ram, two 750s and a dyno to tune it. If you only make 450 then you quit the pull early lol.

I think a buddy has a set of hooker 5204s for sale if you are interested.

I have one in my car and have been happy with it. I have been beating on it a fair amount over three years and it still looks good, not many miles on it though, still isn't completely broken in lol. I will be running it in a couple weeks with what should be close to 600hp and a clutch tamer so...

You should have seen the group of them heading into renegade on Friday night before the mopar drags. We were behind them at the gates and we all just started laughing our asses off at the customized plates and corvette hats. At the end of the day I am all for whatever someone wants to do and it...

Leave it to you to talk about corvette guys on a mopar forum. You sure seem to know a lot about chevy folks, jeesh, next thing we know you will be doing threads on porting LS heads :lol:

If I had your car I would throw some interior in it and drive the hell out of it. That's what my car is for, it has an 8 point cage, wipers and electric bmw sport seats! lol.

Comp hydraulic flat tappet thumpr cam and lunati microtrol lifters in a chevy small block, Comp claimed the cam was good after sending it back for inspection but replaced it anyway. @Newbomb Turk had checked the lifters before installing them and they were good. The second go around with...

Oh, and Tim says no more hugs, it's ruining his reputation :lol:

It was good to see you and everyone else as well Bill. I thought I would have more time to hang out but it seems if I'm not wrenching I'm not at the track lol. Awesome time and really looking forward to Woodburn!

You were a bit red my friend lol, and that is saying something:lol:

I will be there tomorrow night through Saturday with a couple friends. Looking forward to seeing the engine out of my dart make some passes in my buddies race car. It was never going to make passes in mine since I am building a new engine so it will be cool to see it run. See you there Bill, and...

If only it was still together!

Nice ride!. The cam is not the problem since my buddy has a 246/250 on a 108 ls flat tappet cam, ported victor, 10.1 compression in a 408 and it doesn't suffer from lack of low end in a heavy short bed dodge. His engine made 500hp/500tq and he has 4.56s with 30" tires, I think the 3.91s would be...

I will be joining you there since my engine won't be out of the machine shop for another month and the engine that was in the car is now in a buddy's race car. My goal is woodburn in August, it might even be my first outing with the car but there are three days of racing starting Friday...

Did it work for you? :)

I get that, I know my car won't be running to it's full potential for a while. I will be happy just to run it this year without all the extra bs of going 9s yet, shoot I already have to replace my dam belts and never got a pass out them lol. My car is 3350 race weight and the engine should make...

Yeah thank uncle Tony the dipshit for going public with the Vermont tile thing and making it go viral. Sad to say but once the masses know about something good they seem to exploit and ruin it every time. If the wsp give you a hard time have a buddy from another state register it and "sell" it...

Nothing better than a street legal race car!

Like a roasted marshmallow, crusty on the outside but soft and gooey on the inside :lol:

With everything going on I forgot all about the T-ram setup, it's only one more intake lol, I'm game if you are

Thank you and I really appreciate the offer but I think we are good with the heads we have for this test. What we really need is a trickflow intake, I ordered one quite a while ago and the date keeps getting pushed further out, I think it is estimated to be in July now!.