Search results for query: *

I would try a new battery in the remote

I have 2 440 for sale one is HP the other is standard. I have 360 out of truck complete. The 440HP has the original 727 transmission with it. 440 HP has original jentensen distributor and exhaust manifolds. HP needs one sleeve the rest still have factory cross hatch showing. Cylinder that needs...

My pal had a 71 road runner 440 six barrel 4 speed, butterscotch sold it $5000. An other buddy had a T/A challenger plum crazy sold it $6000. Another 71 Demon plum crazy 340 $3000. Another 69 Dart hemi orange 340 4 box $3500. One of my friends has a 70 dart hot pink 340 4 box bench seat he...

I remember the smell of running them in my room.

My Mancini dropped base clears the electric choke on my 600 Holley.

I knew someone would catch that! I have short, fat fingers!

I’ve got the upgraded magnum Hughes springs in this car

Man sounds like a good setup, you got vids of her running?

I like this cam for a modern version of the 340 cam. https://www.summitracing.com/parts/cca-20-309-4/make/dodge

Thank you sir. I’m slowly chipping away at it, and the 4 speed conversion for the duster. Too many irons in the fire sometimes

if, keyword if...

I like apple pies. Just sayin.......

Hi Rick. Thanks. Rotors of various makes can be found. But the hubs are weirdly separate from the rotors and they are very hard to find.

Fact check and I did it myself. LMAO

I like my "OLD" simple stuff. I hear people spending thousands to gain .20 in the quarter. I don't get it, when the consistently maters. Chrysler did it right, with DC help.

I am going to have to use a dropped base. Problem with an Air Gap and a Holley Electric Choke is apparently the Choke clearance. I will tackle this after it is running.

3d print in plastic to inconel to all kinds of other materials is available. You will have to either hand finish the part or pay a LOT to avoid the rough stepping on complex surfaces. 3d print the plugs, and hand finish the surfaces, and molds can be made for fiberglass, carbon, or kevlar. This...

Kindof like me, lol

The brake dust shields should be galvanized steel, which is one of the best ways to prevent corrosion on metal. They're probably eletrogalvanized rather than hot dipped, so the zinc coating likely isn't super thick. But the reason they don't look detailed is because of the combination of brake...

That'd be great. I'm a little way out from finishing the motor. Just let me know. Thank you!

Too late. This whole build is themed cheapskate. Lol

The old boxes were half gallons. 64 oz. These plastic containers are 46 oz. (.3459 gallon) and they have been used for years now.

The factory would have sprayed the whole thing blue and the exhaust manifold paint burnt off.

@Dana67Dart What are your dimension limitations?

Barracudas need a good offset, not as much room at the front of the fender as a Dart or later a-body. I had 2 different sets of Cragars on the front of my 67 Barracuda, and it has the stainless wheel trim, neither rubbed: 14x6, 4.125 bs, with 215/70/R14. 14x6, 3.75 bs, with 205/70/R14. Now I...

Seat adjuster knobs

What ecu was on the Cuda? I didn’t say “all” aftermarket ECUs were good.

Local Amish butcher shop sells butter pecan in 3 gallon buckets

Why have I not previously known of the Henry Supreme!!???

I've got an 05 Ram that is 20 years old. It has 4 oxygen sensors, one just went bad and I was lucky enough to replace the right one. In the 20 years never failed to start. I had one EFI go bad on a 71 Cuda and it was the ECU that went bad, again truck flat bedded home. Next day started fine, ran...