Search results for query: *

I am thinking of putting a ralley dash in my 71 swinger.I have read a lot of threads on ralley dashes and sounds like more trouble than its worth.Is there that much trouble with the wiring.They talk about voltage regulater running fuel gauge and other gauges and having a lot of trouble with this...

Hello everyone.Im wanting to put a rallye dash in my 71 swinger but was told I cant put a non ac heater box in place of my a/c box because the heater motor is in the wrong place.I want to get rid of the A/C all together.My ralley cluster is not an a/c cluster.Is this true,and if it is what can I...

Is there a way to bypass my factory ampmeter since I have the aftermarket gauges.When im driving the amp light flickers and my lights will dim and I don't want it to go a fire.Thanks

I have a 1971 Scamp with a slant six 1 bbl.I put a 2 bbl carb and intake on and was wandering what I could use for linkage and kickdown.The tranny is a 904.Any help would be great.Thanks

Hello everyone.I pulled the motor out of my Scamp and decided to clean the engine bay up some.There is stuff like yellow glue and rust check all dryed up all over.I tried varsol and it wouldn't touch it.The paint is good under all this crap and don't want to ruin it.I tried lacquer thinner and...

I bought these seats from a guy who said they were out of a Duster.I also got a complete set of new seat covers for front and back.When I got home I checked out Legendary Interiors web site and found out the covers are for a 1971 Duster.I checked all the seat patterns and cant find anything that...

Can anyone tell me what these manifolds fit.Part numbers are 2863553 and 2863543.A guy wants 200.00 dollars for set and says they are 340 manifolds for an A body.Dont want to buy them if they don't fit.Thanks

I am putting buckets and rear seat out of a 1972 Duster into my 1974 Duster.I know I will have to drill holes for the buckets as I have a bench now but will the back seat fit in.Thanks David

I have a reverse light for under my dash and not quite sure where it goes.For some reason i thought it went in line with my wiper switch.I just want to drill one hole so i want to be sure.Any help would be great.It is a 1974 Duster.Thanks

I hauled the dash out of my Duster to put another one in.The old dash was butcherd up.The dash pad is brown and would like to paint it black.Anybody know of the right color and type of paint or dye to use.Thanks

Back again guys.I just did my 318 over,rear end has a set of Richmond Gears,355 with sure grip,and a 4 speed.I put the car back together and now i have a vibration and a whine in the rearend when you let off the gas,no very little noise under load.The axles also have green bearings on moser...

was wandering if a 73 or 74 dart front bumper will fit a 74 duster.Thanks

I did a compression test on my 68 318 before i take it out to paint.The drivers side from front to back was 145,132,145,160 and the passenger side was 150,150,175,145.What im worried about is the 132 and the 175.can anyone tell me if this is alright or do i have a problem.Thanks David

Clutch going bad on the Duster and was wandering about a 3 finger zoom clutch.The motor has around 310 hp with 355 sure grip.Thanks David

I have a 1969 318 with a 455 purple shaft cam,edelbrock intake,600 holley carb and hedders.The problem im having is the car will start pinging when it gets around 180 degrees.I tried setting the timing at different degrees and nothing helps.Tried running boost and that dont help either.Read an...

Would a 1969 318 crank out of a automatic car have a pilot hole for a standart transmission.Thanks David

The throw out bearing makes a noise with clutch out and stops with clutch in.It is a 10.5 on a 318 motor.Tried adjusting with only 1/2 pedal made a little differance but if i adjust it any more the pedal will be 3/4 down to the floor before it engages.I still have the overhead spring in it...

I have a 74 Duster that started howling when under load and quite when you let off the gas.Took center section out to check it and found out i had moser axles in the 8 3/4.Now i need to find out if these are the green bearings i hear are no good.There are 355 gears with a shir grip.Any help is...

Can anybody tell me the length of drive shaft i need for a 74 Duster with a 489 83/4 rear end and a 4 speed A 833 from center to center.Thanks David

Took the Duster for its first drive since i bought it and shifted great from 1st to 4th.Then went to stop and down shifting from 4th to 1st and every gear was crunchy going in.I have a centerforce clutch.With the car out of gear and clutch out there is no noise,but as soon as i put it in gear...

are all Dodge and Plymouth rear spring hangers the same,and what years had them.Are A,B,C and f bodys all the same as a 1974 Duster.If not can the old ones be fixed.The bushing tube rusted out,the rest of it is good.I know mancini sells new ones but 2 week delivery and im ready for them...

Can anyone tell me which way the bolts go in and is the lob up or down.It is for a 74 Duster.Any pics would be very helpfull.Thank You

Bought a 1974 Duster and the bumpers are painted.Would like to put chrome bumpers on.Will 70 to 72 bumpers fit or do i need 73 and 74 bumpers.Thanks David

will a 1971,72 front end bolt on a 74,75 duster without much trouble.Im talking about fenders,hood,bumpers.Thank You David.Bye the way im selling my Dart,17000.00 or best offer

i have a friend of mine with 1972 plymouth duster 340 auto consol with power drum brakes.WE CANT FIND A POWER BRAKE booster anywhere.Is there anything else that will work.Thank You David

i have a 70 340 stock block, j heads,268 comp cam,edelbrock performer intake with 800 thermo quad carb.Motor was rebuilt and have no more power than a 318.What could be the problem.Distributor was curbed,running no vacum,coil shows 9.95 volts at distributor.Timing is at 14 degrees,36 initial.It...

i have a 70 340,268 comp cam,600 edelbrock carb,stock heads and virgin block.Motor was rebuilt last winter.car runs good until you floor it then the pinging starts,sometimes it will ping going up hills.tried other carbs,no good.i run octane boost,no good.tried lead suppliment.no good.i burn high...

i have a 1970 340,501 lift cam ,4 speed and 323 83/4 rearend.I and looking for a good carburetor to put on it.Iuse it for manly street.Any suggestions would be helpful.Thank You David

will 10 inch backing plates and drums off a 71/4 fit a 83/4.Going in 1967 dart.

are 67 dart 9 '' spindles the same as 72 dart 10'' spindles.