Search results for query: *

Thanks for the help with the gauges on my 68 fastback. So I tested the ohms on both the temp and oil. They both seem around 20. I took 2 AA batteries to make 3 volts and was able to move them both about half way. The gas gauge. Looks like my dad's work. You can see the lip is all banged up. He...

6 It's from a 69 fastback. Rally dash. So I took in to have it tested. Mechanic says all the gauges are fried. There is an external voltage limiter that was soldered on?? He says this shouldn't be there?? Mentioned that voltage regulator is part of the fuel gauge? Any idea where to buy...

So my gauges still aren't functioning. I believe it has something to do with the ground for all of them. I was told this is grounded through the dash attachment screws. I also seem to be missing the top metal plate that goes on the dash as well. Thinking this might be the issue. Seems all the...

Got it all in. Thanks for the help. It was a p Got the carpet in. Thanks for the help. Only made one bad cut. Cant see it anyway.

The other end where the finished edge meets the center console mount?

Got my carpet ready for install. I don't have the original so I'm struggling trying to get it right. I got the first part in (back seat area). Might have trimmed a little too much so I dont want to mess up on the front part. It is an auto with a center console. I lined up the molded parts of...

So I guess i need to have them in the car then because of the screw holes behind the trim?? Install then put carpet on?

I got new cargo area carpet for my 68 fastback. Looking for some tips with the install. What's the best technique for the install? The side wheel covers did not have carpet but I wanna put it on there. Do I use the L shaped trim? Does a bit of carpet go under it? Does the carpet go under the...

My fat fingers found it

Headlights aren't working on my 68 Fastback. I believe it is the ground. I have 12v at both high and low beam. Where does the ground connect. I have grounds for the inboard turn signals that are connected to the rad support, but i cant find where the headlight ground is?? Where would it be on...

Is there a ground for either the headlight switch or the instrument cluster?

Thanks. Cig lighter of course. Thanks again

68 fastback

This one is an L-shaped connect with red and white wires. I believe it has something to do with the right side floor area. The yellow wire (male)I believe goes to the door sensor and the other red(female) goes to the under dash light. Wondering where the L-shape connection goes?

Trying figure out a few missing connections on my new wiring harness. This one is a black one joined together with the red and white ones that connect to the brake pedal. The first one is in the car, the second one is the original wiring harness.

Thank you so much for the help. Got same click in park. Moved it to neutral and it started right up. Guess that means I need a new neutral safety switch?

So I've got a starting issue with my 68 Fasback 318 auto. Can't seem to get it to start from the key. I can get it to start and run by using a hand held switch at the starter relay with the key on. There is a brand new inside wiring harness, starter relay, ignition switch, and fusible link. When...

I found your thread. Oh crap I hope I don't go down that rabbit hole. I just wanted to replace the seal and clean it up.

Took mine apart yesterday well at least got the reservoir off. I guess I need to get the tool to get the pulley off. Does it just get pressed back on when putting it back together?

For my 68 fastback I count 23 holes for the clips does this sound correct? 3 on each side 9 on the bottom and 8 on top?

Slowly putting the puzzle back together.

Thanks

Getting ready to have my windshield installed.(68 Fastback) The installer claims that not all clips for the windshield are made the same. He said he has issues with the ones from Classic Industries. Is there another place I that I should get them from?

It’s leaking when the engine is shut off. What could that mean?

My dad is the original owner and it’s still all stock. I wanna keep it that way so Im trying to stick with the carter. I actually have an aluminum intake and a performer to go on but I was trying to keep the original one.

My carter bbd is leaking from the from the throttle body linkage. Its the original carb on the 318 in my 68 fastback. Is there a bushing that can be replaced on the shaft?

So I had some credit at Classic Industries so i bought their glass channels. WTF?? 99 bucks for for that? Anyways, it came with the h pins and the black channel. Still confused how this all goes together. What needs to be hole punched? What attaches with the h pins? How much of the black...

Any idea where I can get it?

Is this what I need? Does that go in the vent window channel? Door Window Glide Strips for 1967-1974 MoPar A-Body | eBay