Search results for query: *

You can see additional restoration photos here: https://photos.app.goo.gl/PQf5Bu1fZ1pGpjeb9 Car was painted factory color BC/CC (Diamont base/SPI clear) by Mike Roeder at Roeder Restorations Auto Restoration at Roeder Restoration

Here's your chance to own one of the nicest 64 Darts you'll find at a great price. Only listed on FABO, I'm asking $9,500 for my 90% restored 1964 Dodge Dart GT push button automatic with the original slant six located in Springfield Missouri 65804. I purchased the car about five years ago and...

Hi Ulf, I'm looking for that rubber grommet for the radio cable pictured here. Do you know where to get one? Thanks, Robert

I'm pretty sure it was only on the door (at least for my 64). I will let you know the width and send pics if you need. Thanks for the tape info...I won't tell anyone it's not NOS :)

The door panels look great Ulf! Are you planning on adding the white reflector strip to the front door stainless trim? By the way, what type of tape did you use to secure the plastic?

I've been researching this as well. Here's a 1964 Chrysler video that explains some of this. It appears they use sealer when putting back in the glass. Look at the 13:00 minute mark. https://www.youtube.com/watch?v=bY4kgO8cyDU Here's another video from 1975 that goes more into depth...

The headliner looks great, kudos to the installer! I had a new one put on my 64 Dart but they didn't tuck it in around the back glass like yours. I'm thinking of having it redone. Can you tell me where you got your headliner from?

Hi Ulf, quick question. I noticed you took apart your vent windows and put in new seals. I'm thinking of doing the same on my 64 dart. Looks like you had to remove some rivets to remove the old seals. Was it a very tough job? My seals are pretty good but I have already rechromed all the vent...

Hey Dallas, thanks for the reply and the encouragement! I was hoping to be further along by now but with a new baby there are somethings more important :) That's about the clearest advice I've heard on the back glass sealing. I'm sure I can find the part number. Do you like to seal things...

Here's a few more pictures of progress (slowly but surely) on the dart. Next up is getting the back glass in. I want to make sure to get it sealed properly (even though the car probably wont see much rain) so I've been reading on here on how best to do it. I like how the headlight rings...

I'm getting ready to put the trim around the back glass of my 64 and was wondering what, if anything, I should put between the body and back glass stainless trim as seen in the picture below? I have dum-dum tape and have also have heard of using insulation weatherstipping from lowes or...

Just looking for one of the older style. PM on it's way.

Thanks for the tip! I know the earlier ones tended to crack. This may be a good alternative if I can't find an original type.

Looking for an early slant six exhaust manifold in good shape for my 64 Dart. Should look something like this... Thanks!

Here's some information that might help. I am using the limiter which I purchased from RTE on my 64 dart. They are no longer in business so I'm not sure what would be the correct one to use instead. The picture from ebay looks similar to the one I used but not exact. You might call D & M...

Hello, I'm looking for a rust free splash shield for my 64 dart. Just need the passenger side rear one. Thanks, Robert

Hello, I'm putting back together my car and am needing the part shown in the picture below. I unfortunately broke a stud on my rechromed piece tonight. That's only $200 down the drain (ouch). I have another one but it's pitted pretty bad so it wouldn't be a good piece to rechome. Just...

Hello, Looking for a good condition drivers side stone shield for my 64 dart. Thanks! Robert

Wow, thanks everyone for the help! After your suggestions I think I have enough information to get started. Now for a trip to the hardware store. I also like the suggestion of the drill bit. I never had heard of a roll pin before. I've been reading this link on restoring the windows and...

Thanks for the tip RedFish! I'll try to locate one of those drift punches. Looks like the other piece may just be glued in after checking my parts book. I'll see what I can figure out. Thanks again!

I need to send some parts out for re-chroming and am trying to figure out the best way to remove the chrome handle from the chrome base. There is a small pin in the handle keeping attached to the base (shown with the arrow). Any tips on removing the pin? Also, I need to remove the window from...

Sounds like a good plan! Thanks VDART!

I'm putting back together my 64 dart and have always noticed that the antenna looks bent at a slight angle at the base. Just wondering if this is correct or if I should try bending it back. I'm a little worried about doing more damage trying to bend it back. If any one has experience with...

Great, thanks for the help and tip! Sounds like a good weekend project.

Hello Dallas, Good to hear from you. I took your advice and posted on the body section. Things are going a little slower than I'd hoped but I think I can get it back on the road this summer.

I'm needing to disassemble the vent window for my 64 dart so I can send the pieces of to get replated. From the exploded diagram it looks like I need to remove the pin from the handle assembly shown below. Any suggestions on how to do this or advice on the correct approach would be much...

Thanks! I didn't mean for it to end up this nice (wish I had the $$ I spent) but after all I've done to it I want to make sure take my time and finish it right. You should share your progress too. I'd like to see another 64 on here. Let me know if you're looking for anything in particular.

Starting to work on the Dart a little more after a long winter. I picked up some NOS antenna bezels (first pic). Need to figure out a way to straighten out my antenna. Might be a good reason to buy a vise for my shop. Also, I need to disassemble vent window for replating. If anyone has any...

I got a set of the Vent frame gaskets from Gary Goers (http://www.garygoers.com/). These may fit as well on ebay from valleyvintage.

I believe I got mine from The Right Stuff (getdiscbrakes.com/transmission-vacuum/transmission-cooler-lines). I talked to Curtis. There's also inline tube. I'd heard that the right stuff lines fit better.