Search results for query: *

I'll take it. Thanks. Just shoot me your paypal in a PM and I'll send payment along with my address.

Hey Scott. I am going to pass on the console. Thanks for the extra pics, it looks like a good deal for someone.

Interested... Do you have any more pics?

Originally yes. Now in front of an 8 3/4, hence the conversion joint. So, change the rear conversion joint to a normal 7260 and it will fit the 7.25 again. Thanks for pointing that out.

Drive shaft for sale from a 74 duster. Measurements are as follows: Center to center of u joint: 47 1/4 inches Circumference: 9 1/2 inches Total length: 54 7/8 inches Yoke fits a 904. Front joint is a 7260 (small joint) Rear is a new 7260/7290 conversion joint Macon GA. 100 plus...

Put me second in line if anything should fall through with the sale. Thanks

Thanks!! I have emailed him and asked if he would ship just the pulley for the 10 dollars asking price... I also have the CVF pulley in my cart on their website and will go that route depending on what the outcome of the craigslist ad is. Thanks for all the help guys....

Close, but i think that one has a larger/ longer snout on the rear of the pulley that may effect alignment. Here are some pics of my pulley

I am only able to find the March pulley, which some have said is not a perfect fit as far as alignment goes, plus the cost. I really don't want a shiny pulley either... There is almost no chrome on the engine as it is now. Murray, who are these p/s rebuilders you mentioned? Like A1 Cardone etc...

Hey Guys, I am in need of a pulley for a Federal power steering pump. I already have the new pump, but bent my pulley as it was FROZEN onto the shaft. It is a 5/8 ID press on (no keyway) pulley, 7 in dia. Please let me know what you have and how much. Thanks

Hey solid340, I need the same thing. Where did you wind up finding a pulley if you don't mind me asking

Update... After taking the block to Wheelers and I believe just about everyone in the shop coming out to take a look, they all agreed that: 1) As many of you stated, the sleeve was set too deep in the block. That left the register too thin on the one side, and thus the small piece of the block...

Perfect. Thanks!!

Well done sir... I'm with 340doc on wanting more info please....

Wow!! That is a beautiful car. Enjoy it

That is 100% correct. The sleeve appears to have been pushed in too far and a piece of the block chipped off. This piece that chipped off is paper thin. RustyRatRod, thanks for the offer, I am taking the block to Wheelers machine shop downtown Macon tomorrow morning to have them inspect it. I...

Macon GA

Just walked out and looked at the combustion side of the cylinder and you guys are correct. It is definitely a sleeve. The motor was recently in the machine shop. It was bored to .040, mains were line bored and the short block was assembled by the machine shop. If they placed the sleeve in it...

I do not think it is a sleeve.. But I did kind of have that same thought when I first saw it. Of course anything is possible as I have not always owned this motor. Is there a tell tale sign that I can look for to see if this cylinder is sleeved? I do not see any obvious differences between this...

RPM AirGap in my opinion

Hey Guys, I have a 418 that was recently put together/fired up and began mixing water and oil. I pulled it back down and on closer inspection I believe I have found the issue. My question is what are your thoughts on fixing this? Can it be sleeved? If this can't be saved/sleeved etc, what are...

Hey Gary, looking for some 72 340 side stripes; are you still selling these? If so, what it would be for the 72 340 duster side stripes in matte black? Thanks

Congrats!!!!

SOLD pending payment... Thanks FABO

SOLD!!! Pending Payment and shipping. Thanks FORABODIESONLY

Hey All, I have a Torker 340 for sale. I ran it a few years ago but it no longer fits my build. Just needs a good cleaning. Asking $50 plus the ride OBRO. Paypal preferred. Thanks

Hey All, I have a set of M/T valve covers for sale. I ran them years ago with no leaks and they have been on the shelf. I cleaned one to show the 'potential' a little elbow grease could give them. Asking $75 plus shipping OBRO. Paypal preferred... Thanks

What they said... Call someone and have a converter built for you car. It WILL be worth the extra coin in the long run. I called PTC and had one built for my setup. Couldn't be happier

Could have sworn I flipped that before uploading. Oh well, here ya go....