Search results for query: *

Hey guys and gals I am thinking about trading my jeep in on a pickemup. I gave info to Carvana and checked out some deals. They seem pretty fair and have some what would appear to be good deals. Anyone use them or know anything about them? Thanks for any responses. Pike

Anyone attend? It was a hoot!

Hi forum friends. RealOT question I have an led dawn to dusk light on the end of my shed that has started flashing instead of operating normally. I checked connections and put a new switch on but no go. No luck on Google. Any ideas? Thanks

Howdy Not a mopar but....I have to put a new head gasket on a 25 year old merc 2 cycle,25 hp. Should I use gasket sealer and what torque for the bolts? Thanks for the help Pike

Grilles and inserts with lamp housings. Rt housing pitted and a fin repaired on rt grille. Otherwise decent shape $175 plus shipping

Nice shape dash. One tiny pinhole in dashpad. $350 plus shipping.

Pair of bucket seats from a 68 cuda. New legendary covers need a little tweeking. Tracks incl. $650 plus shipping from 54758.

Seems nice and tight. Includes arm 100 plus the ride

1/4 so need a little work. New drive. Side floor. 1000 takes it

Hello all. I have a 68 Cuda vert project I am having trouble with. It is stripped down to the shell pretty much and I have all the parts, bagged tagged and scattered about. I am a little over my head as it needs some work underneath, not a lot I don't think. Also the 1/4's need a little work. I...

I am unable to finish this project and would like to sell it as is. Its a 68 Cuda vert dissasembled. All parts are here in various condition but most OK. Buckets are recovered with Legendary covers. Trim is all here but needs a little work, mostly elbow grease. Nice dash and guages. It's a / 6...

I have a 68 Cuda vert that I want to put on a rotisserie. It is all stripped including susp. etc. If I use the bumper mounting points will I be close to the center for weight distribution? Should I go lower or higher? Thanks Pike (the photo still has susp. on. Gone now)

68 Cuda PS steering gear. I am removing it. Is there more than the 2 bolts and arm? Always seems to be something hiding on me

Howdy- I am taking the front of my 68 Cuda apart and am having a problem with torsion bar removal. Working on the right side. I got the adjuster bolt about halfway out with much difficulty. Lotta PB blaster and liquid wrench and a 3' breaker bar. It's really stuck halfway out and I don't dare...

I am ready to work on the underneath of my 68 Cuda vert. I don't have access to a rotisserie so was toying with the idea of putting the bumper brackets on the shell, bolting pieces of angle iron to them and using engine stands front and rear bolted to the angle iron to make the shell rotate. I...

I have my cuda pretty much all stripped and primed. It had the original primer and paint plus primer and recoat w/enamel. A real PITA. I sanded and used stripper. I am down to the cowl and need to know if there is a way to do the vent part without distorting the painstakingly straightened vent...

I have the door disassembled all but for the vent window frame. I took the bolts etc. out that appear to be holding it in but it will not come out. seems something inside the door holding it. Am I missing something? Nothing in Haynes manual. Should I stick to motorcycles and woodworking?

I am working on a 68 Cuda vert. While stripping one of the doors it occurred to me that I don't know if the black on the inside of the door should be painted before the red on the exterior. Does it matter?

I picked up a 68 Cuda vert a few years ago. Not bad shape for a WI car. Had been in dry storage 30 years. I disassembled and welded in new floor pan driver side. Did a bad job on welding lower fender panels. They were toast. Build sheet says /6 but I bought without motor. Picked up a low mil. /6...

Hello all. I am sort of in a conundrum. I picked up a 68 Cuda vert. about 1 1/2 yr. ago for a project. Pretty complete except for motor. I have since picked up a /6 which was in good shape til it tipped over while on the engine stand.(don't ask) Anyhoo, I lost my job a while back and have no...

I finally got a slantie for my 68 fish vert. I also picked up an engine stand. I can't figure out where the 4 points of the stand bolt into the engine. Any help or pix? Thanks Pike

Hello to all. Have been using this forum for getting parts and help with the resto of my vert which is now in many pieces. Just did the bucket seats and have now turned my attention to the doors. (A.D.D.) Anyhoo- was trying to get the vent window out and following the haynes (pains) manuel...

Hi all Working on my 68 cuda vert floors. The rear floor corners (under the back of the rear seats) are rotted right in the corners, about 4" square. Very solid aroun the holes so I would like to just cut out the affected area and weld in new corners. Problem is I have no way to fab new corners...

I am restoring a 68 Cuda vert. It was built w/a /6 but I got it without a motor. I am trying to keep it as original as possible with a few exceptions. I did pick up a /6 with trans from a 68 Dart. What color should the motor be as it came from the factory in the cuda?

Working on the framework for the top on my 68 cuda. The material inside the channel on the rear bow was rotten so I removed it. Anyone know what this material is and where I would get some to replace it? Thanks much Pike- the topless

I have the 225 from the 68 Dart to put in my 68 cuda vert. I see on the "new" motor that the intake man. is tapped on top. I assume this is for a vaccume guage? My cuda doesn't have one but I would like to add one. I presently have the instrument panel out of the car so it would be a good time...

I have a 68 cuda vert. I got it without engine or tranny. It previously had a 225 in it. I picked up a 225 from a 68 Dodge Dart. Anyone know what I am going to run into when I decide to install? I already noticed the tranny on the "new" motor has a three prong plug and the cuda has no female...

Hi I'm Pike. I have been reading this forum for a week or so and it is great. Already got some help from RedFish and others. I picked up a 68 Cuda convert. a few weeks ago and have it in my shop mostly dissasembled. What a hoot! I bought it with no engine or trans. but it was a slant 6 veh. when...

Another on my 68 cuda vert. I got the fabric top disattached from the trunk area thanks redfish. How is it attached at the sail panel area and the front part above the w/s? I know I seem a little ignorant but my service manual doesn't adress converetibles. Sorry Pike- the well read

am working on my 68 cuda convert. Have moved to the top and need to remove it. The fasteners that hold the fabric to the sheet metal around the trunk section are something I have never seen before. Anybody know what these are and what kind of tool I beed to r&r them? Thanks for any help Pike-the...