Search results for query: *

I'm selling my first mopar, hope she goes to a good home. Asking $2500, it's in Jefferson, OR. Here's the link http://salem.craigslist.org/cto/3650067262.html

I need some help on the the parallel 2bbl conversion is setup. If anybody had pictures it would really help. I can't figure out how to get the throttle cable to fit properly. All help appreciated.

So my ammeter burnt out with a puff of smoke and I was wondering if I had to replace it or just bypass it? All help appreciated.

My slant six needs a different air system because it has to little of space for a regular air cleaner. Any ideas? All help appreciated.

My slant 6 with a two barrel runs for a few seconds and then dies. I can keep it going if I floor the gas pedal repeatedly. It's an 85 engine and all the hoses are hooked up correctly to the carb. Any help appreciated.

I need the automatic kickdown linkage that they used on super six setups. I need anything wheter its the whole set up or a single piece or even something home fabricated. Just need something so my tranny won't burn up. Any help much appreciated. I also have a holley 1945 and a sandcast aluminum...

I want to buy a holley economaster for my /6, I heard they bump up fuel economy and drive-ability. I can't find any on ebay. A 1bbl or 2bbl, doesn't matter to me.

I'm not an expert on carbs so I don't know if this is correctly hooked up. Some lines are blocked the there's a wire that isn't hooked up and I can't find any loose wires to hook it up to. Any help appreciated.

I have an original 1920 holley 1bbl, came off a 1973 Dart. Shipping from Oregon. Asking $20+ shipping. Ran when pulled off.

So my dart was running rich so I changed the float level and changed my spark plugs and now the car won't turn over. The starter works, it just won't catch. At first it turned on then the rpms started to go up from 500 to about 650 then the engine died and it won't turn on. Help please, I have...

My 1974 Dart Swinger gas gauge has always been giving me problems. First of all when it says empty it will fill up with 9 gallons and then say three fourths of a tank. Also I just put three gallons and it went from a little below empty to empty. I don't know what's going on and it's kinda...

How does the 4bbl intake improve the slants power? That and how do you link up the carb to the car? Do you have to fabricate a throttle cable and do I have to switch to a manual tranny or can I keep my 904 automatic? Any help appreciated.

I have shackle hangers right now, and I want the original rear leaf spring holders. The piece that holds the leaf spring to the rear part of the body. Any help appreciated.

I want to buy a nice dashpad, something that doesn't have cuts or cracks. Fading is ok. Preferably black or tan.

I want to buy an aluminum intake for my slant six.

I want to buy a two barrel carb, whether it needs a rebuild or not does not matter. Any help appreciated.

I'm looking a super six setup. Intake, carb, kick down linkage, everything but the exhaust, but if it has the exhaust I'll still buy it. Any help appreciated. Can be pieced out, I mostly need the two barrel intake.

The rear windows on my 74 Dart Swinger are needing some attention because they won't roll up or down. This is the first time I've worked with the interior of a car, so to get to the window do I have to remove the rear seat? How do the panels come off? any help appreciated.

I want to buy some center caps for my size 14' 4.5 x 5 rally wheels. I don't need the back wheels I need some for the front wheels. I have disc brakes in the front so the center caps I have on my back wheels won't work for the front wheels. If you only want to sell a set of four still pm me I...

So I was trying to change the gaskets on my 225 /6 and when trying to take the two nuts on the exterior of the exhaust, the two nuts that are on each end of the engine that are supposed to be brass, the studs started to come out with the nuts. I know that the nut must be rusted to pull the stud...

I'm looking to buy a 1bbl aluminum intake for my 225 /6, something like what they had on the Dart lites and feather Dusters.

I need a wire diagram and fuse box diagram for a 1974 Dart Swinger. Any help appreciated.

I need a 225 /6 air filter system for my 1974 Dodge Dart.

I need help figuring out why my 1 cylinder spark plug keeps fouling up. It gets saturated with gas and won't spark. I recently got a 1920 Holley 1bbl and rebuilt it, but I don't know if I got the float right or the air/gas mixture screw in the bottom of the carb. Any help much appreciated.

My 225 /6 was working fine then all of a sudden it started misfiring. I'm thinking it's the distributor, but I have no solid evidence yet. Just wondering if other people have had this problem and how they fixed it. Any help greatly appreciated.

I need help with how the linkage of the wipers work, I connected the shorter arm from the motor to the drivers side, but from there I'm lost. Also how to adjust the entire wiper so it can wipe a more wide spread area. It is a 1974 Dart Swinger, any help appreciated.

I need a carburator for my /6, the one it's got has seen it's best years and is gonna die soon. Just wanted any advice on where to get one for cheap, and what kind to stay away from.

I need rear brake lines that go from the proportioning valve to the brakes and I need a proportioning valve. What's the best place to get them? Any and all help appreciated.

I was wondering if anybody knows where I could get a 4inch by 5 set of wheels for a 1970 Dodge Dart sedan.

I'm trying to pop out the brake cylinder on my brake calipers and it's not work. I've tried air pressure and brake cleaner to loosen it but it won't budge. All help appreciated.