Search results for query: *

Stay away from the Ford cable regulators. The cable snaps easy. My friend has a 2005 F250 and he has to replace it. Hmmmmm I might have to the same to my 65 dart. I work at a part store so I will have to look around for the motor. What year did u get yours out of?

Do they work for 65 Dodge dart?

Hey DJVCUDA what kind of return line did you used on your set up. What type of ignition system do u have? Got any pics of it? I have the old points system and want to up date it.

Still go them

Do u still have the a-pillars?

I just order mine kit from Jegs and got it 400 cheaper buy using there price check from e-bay. I cant wait to get it on my 318. I have been around carbs cars and hate to tune it. If any one needs the link for e-bay PM me. And yes it was the kit with the fuel lines and pump. It will be awhile for...

I am try to find A-pillar parts for my 65 dodge dart. Does any one know where to get it? Mine are in 4 pieces and the screw holes worn out.

Last week I work on restoring the A/C and heater box. I found a kit that had all the pieces to rebuild them. The kit was complete but I think they cut a few pieces to short. Came out looking good. When I open A/C box I found alot leaves and stuff in it. Clean it all out and rebuild it. Don't...

Who has pics of the Dakota Digital set up?

I am trying to see if Dakota Digital would make a set of gauges that would go into the factory dash panel. They are saying that they can put in 6 gauges in the panel. It will be around 1100 for it and the sending units. I am waiting on a email back

I am trying to find out how many 65 dart guys are looking for Analog/ Digital Gauges for there cars?

Do u still have it PM me

Is it sold

I wish I could find someone that makes a dash kit for a 65 dart. Anyone????

I like your shop, cant wait to buy a house and build mine. The air compressor from Harbor Freight sucksssss, I bought one and it could not take a lug nut off. :wack: i look around for a better one and found it at Menrads...

Does he have a 904 pan still? Looking for a deep pan.

Do you have any 1965 dart A-pillar for the front driver side? pm me

You have the bar upside down.....I just installed mine and did the same thing, so I flip the bar around and it works

Well I took the unit apart and found the switch just need clean. I test it and it works know. Yeahhhhhh

Where do you get a new from? On my 65 dart the guy who had it before me used a jumper wire. I would like to find a new one.

Here is mine http://www.forabodiesonly.com/mopar/showthread.php?p=1693565#post1693565

Here is a few pics of the front so far and the engine , intake.

Well today I have been painting parts and the engine. Took the engine apart and found alot wrong with it. The guy who had built it only did the bottom end, he replace the bearings on the crank, rods and cam. Well he did not tear down the whole engine or he would have found that pistons were...

Here is good web site to check out http://www.popularhotrodding.com/tech/1104phr_13_rookie_engine_building_mistakes_and_how_to_avoid_them/viewall.html

Try this web site http://www.valleyvintagestore.com/exhaust.html

Keep up the good work. Cant wait to see more pics and how it runs!!!!!

You might want to add some x -braces between the boards that run across. I see one one of the board twisted all ready( the one that has the red wire). If they go then the roof might come down. I would add the every 3 feet or so.

Well I had the front end all together until I notice that the lower control arm was sitting a little far out from the K-frame. angry9: So today I pulled it all apart and shave off a little of the strut bushing. Here is a link I found on how to do it. http://users.erols.com/mathewg/bushings.html...

I have a 270

Still got it pm me if so