Search results for query: *

65 Valiant STREET class race car 408 stroker with "J" heads, 727 automatic, 4.10 suregrip, 235/60 R 15 Mickey Thompson drag radials. Car weighs 3145 with driver. 10.993 @ 120.03 MPH Before and after pictures.

Here is my 1968 Valiant 100 4 door, it started out life with a 170 ci slant 6/auto. It was converted over to a 68 340 4bbl/4 speed with 3.23 sure grip 8.75 " rear, large bolt pattern all around with single piston later model disc brakes up front. This was done by a FABO member and I bought it...

I did the same basic thing using a 1 ton electric gantry hoist to lift the front of the car's (67 dart) body high enough for me to roll the engine, trans, K frame, etc. on a dolly out from under the car. As for installing the engine this way, my next project will done in a similar fashion. I...

Sold!

Sold

grill is sold the two moldings are still available

bump

door sill plates are sold, everything else is available

this bell housing from a 340 is for a 10.5" clutch and has a 4.354" diameter bearing retainer opening. It has had all of the threads inspected and chased out with a tap. Just clean it up, paint and ready to use. Price $150 OBO plus the ride, can also be picked up locally in La Plata, MD or...

the bearing diameter is correct, but an A833 OD mounting bolt pattern is not present on it. it only has mounting bolt patterns for a NP 435 trans (HD granny gear 4 speed) and a truck three speed (?). good for a truck, not a car. price drop $45 OBO

bump

bump

price drop $35 for the pair, plus the ride

I am not sure about if they re hardened it after grinding, but since it was done by a reputable shop I would hope they know what they are doing.

grill sale is pending, moldings are still available

rod journals are 2.100 and have been widened, if they had not widened them I mike of tried to have it reground to 2.095" and use .030 under size rod bearings with my MOPAR roads?

sale pending

sale pending

I have this forged steel 3.31" stroke small block mopar crankshaft, from a 273, that came with a 73 340 engine I bought in parts. The previous owner had had this crank reground, the mains were ground .010 undersize and the rod journals were ground to small block Chevy large journal size. Guy...

these connecting rods came with 67 273 4bbl engine I bought in pieces, the guy I bought them from worked at a machine shop years ago and had replaced the rods bolts , resized the big ends and rebushed the small ends of these rods. they have casting number 2406782. they look pretty good...

not exactly sure what these are called, but they cover the upper edge of the rear quarter panels and Dutchman panel where they meet the bottom of the convertible top. set is NOT complete, has both SS side pieces, SS rear piece and one chrome plated Pot metal corner fitting. The Stainless...

here is the pictures with the straight edge, they valve tops line pretty well. A few valves are down by a little (less than .005") , probably due to some valve stem wear. Each head has one exhaust bolt broke off that will need to be repaired. Heads have some surface rust from sitting for...

it is dark outside , so I will get you the picture with the straight edge tomorrow after I get home from work and get you a shipping quote. thanks, Bob

this pair of Hooker Model 21505 Aero Chamber Mufflers are used but are in very good condition, only used for a season or two on a drag race car they have 3" inlets and outlets and are welded construction, sound great located in La Plata, MD Price $50 OBO plus the ride or local pickup in La...

this set of front splash shields from a 1965 barracuda are used but in good condition, they have bee cleaned up and painted with POR-15, only a small rust hole in each located near the lower mounting bolt hole. price $40 for the pair plus shipping, local pick up in La Plata, MD or at MIR...

I am listing this set of wheels for a friend, they are in good condition, straight with no curb rash, comes with four driver quality trim rings but NO CAPS. Located In Mechanicsville, MD price $125 OBO local pickup only

this set of "308" casting number swirl port heads came off of a running 360 engine that was used for a stroker build, engine had 89K miles and ran well. Heads can be cleaned up to use on a driver or rebuild for a performance engine. come with the shafts and rockers, price $100 OBO plus the...

these parts came from a 1966 dart I parted out a while ago: the grill is in fair condition (sort of bent up along the upper edge of the lower portion in the center region) $20 side molding (not sure of where it fits on what car??) $5 SS 1/4 top molding $5 located in la plata, md...

more trim and stuff for early barracudas: Fold down truck divider panel $30 plus shipping Not sure if this is OEM or not, but it has a hinge, a pair of latches, some bumpers, some OEM looking carpet and SS trim on a piece of plywood, this thing came with a 65 barracuda in pieces a few years...

parts from 65 barracuda for sale: passenger (right) side door , good shape , little surface rust on bottom edge with a small hole (looks like burn through with a torch???), comes complete with both windows with regulator, hinges, trim, etc. located in la Plata, md (35 SE of Washington, dc)...