Search results for query: *

Anyone have a 1963 valiant driver side tail light lense?

I'm looking for parts for new project: 63 valiant tail lights 4 barrel intake for a slant six header for a slant six Thanks

If I turn my turn signal on the lights will come on but not flash, I thought maybe flasher was bad so I installed a new one and it still does the same thing. Four ways do the same, light up but not flash. Any ideas?

Top picture the pressure plate is unbolted from flywheel, bottom picture it is bolted to the flywheel, my question is should the fingers drop that much? With it in the car like that the adjusting rod is fully adjusted to the end of the rod, and the clutch engages right off the floor! Grease is...

Anyone know the size of the centering pin for the shifter box, for adjusting the linkage rods?

I am putting a 75 V8 motor an auto into a 72 dart, the rod that goes from the column to what I call the shifter bell crank, is to long I think? Are the rods from a S/6 to a V8 different?

Anyone know where I can get shifter boot for b-body bench seat car with a pistol grip shifter? The last two I got from brewers performance and they were terrible, they both ripped after several car shows, literally a couple hundred miles! Part #SB755

Does anyone know of a slant 6 head with "special" cast into the head? The casting number is 2206035

Which member, has or does anyone have a picture of the swinger i think it was with an RT hood off a challenger? Thanks

does anyone recall where the article was that, I think it was a father son project, they put a late model Challenger RT hood skin on a 1970 Duster hood?

I'm looking for new glass for my duster, has anyone had problems with the new glass? I was told it is thinner than the original glass? any suggestions? Thanks Dave

anyone have a finned aluminum slant 6 valve cover they want to part with?

anyone have a finned aluminum slant 6 valve cover they want to part with?

looking for a Clifford slant 6 finned Valve cover, anyone have one they are willing to part with? Dave

8 3/4 third member sure grip posi 489 case 5.125 gears $700 great condition

My 225 is getting 198 rods, 2.2 pistons, bigger valves, cam, some port work, shave the head, (hoping for around 9 to 9 1/2 compression) a Clifford 4 barrel manifold, a 390cfm 4 barrel carb, headers, duals with "X" pipe to mufflers out the rear! what mufflers should I use? and what about...

For the sake of prices I'll post some, but make an offer, the worst I can say is no! Fenders $50 hood $50 trunk lid $40 Slant 6 Engine $200 Front Big bolt disc brakes $300 SOLD 8 1/4 posi 3.21 Big bolt rear end with springs and driveline $350 SOLD Doors $75 each Bumpers $50...

I have a 72 duster with a slant 6 and I am putting in a A-833 4 speed and an 8 3/4 rear end, so what driveline do I need?

Wanted Header and Clifford Valve Cover for a 72 duster with a slant 6!

wanted: 8 3/4 for Duster? dual sport mirrors for duster? drop spindles for duster? cop car dog dish caps? Thanks!

I am putting a beefy 360 and maybe a 3.23 rear gear in my duster and was wondering which would be the better way to go as far as transmissions a 4 speed or 4 speed OD? not a racer more of a cruiser!

alternator went bad so I changed it and put a new voltage regulator on it also, now at an idle the headlights are dim, but if you rev it up the lights get brighter???? what do I need to fix?

is there a picture of which cables go from where to where on a 72 duster heater control to heater box? Thanks Dave

I have found a 63 Valiant 4 door needs motor, car is straight, needs paint, and interior work, brake is frozen needs tires, push button automatic, air conditioned, over all in sad but fair shape, any ideas what to pay for it, its best offer??? Thanks Dave