Search results for query: *

Has anyone have lying around in their piles of parts the bottom half of a 1970 Dart Swinger front split bench seat. I need a good frame and springs. Don't need the back upright portions and I don't care about the padding or the covering as I plan to repaint and recover. Mine is damaged and is...

Hey guys, This old fart (eds70dart) will be there Saturday at the Moparfest, but on foot like the last 10 or so years. Probably have seen some of you guys in past shows, and didn't know you guys were members of this site, so I would like to meet some of you guys and see your cars instead of...

Yes I would be interested in the product also.

Sorry I didn't get back to you. I'm having problems getting pictures onto the web site on this matter. But I did by chance find the old part number for the plugs in an old Chrysler parts book and they are still available for about 2-3 bucks apiece. I ordered so I'm going to replace them all. I...

Need some advice here and wether to act on it. Re-doing my rear drum brakes and replacing them with all new stuff. I was cleaning all the rust off my rear back plates, I noticed two oblong holes at the bottom of the back plates. They are behind the adjuster screw assy. and in between the brake...

I have a 70 Dart Swinger, 340-4 speed car. The fronts are disc and rears are drums. The problem is I need a new set of rear drums and don't have the originals to get any measurements off of them to replace them on the back end. Any Dart owners out there that have purchased any new ones. Also can...

Maybe I didn't elaborate enough sorry. The front wheels or front end are on the ramp style supports. I have jack stands supporting the rear end of the car on the frame just in front of the springs where it's bolted to the car. I was trying to get the car up level with the rear part of the car...

This might sound a little stupid, but I rather be safe than sorry. I figure there have been others out there that have done this and know the in's and out's of it. I received my car back all painted on the underside and top side and while looking it over in my driveway I noticed that the rear...

Would like to know if anyone has had this problem and how to solve it. Put new clips and screws in, had the windshield put in professionally, and was putting the chrome pieces back on, when one of the screws holding the clips on the lower passenger side busted off. I don't know if it was a...

Can someone direct me here or give me some ideas. I know in the past there has been some posts on polishing tail-lite lenses, but just can't find them when you want to. I don't want to spend big bucks here on polishing kits, as the car is not a show car but a well restored driver. All these...

Thank-you very much for the info..

Looking at the expanded view of the Z-bar, I've got a question for my own info. I noticed that the spring is on top in the picture. Does it matter if its on top or the bottom, and what is the real purpose of it. I have an idea but would like to get the right answer from the pros.

Thank-you very much guys. If I ever get to see you guys, I owe you a beer or two. My cousin just lost out and owes me a case of 24....YEH>

Just need advice on the right way of doing it. I'm putting my 70 Dart 340 back together and my family member and I have a difference of opinion. There are two or three of these clips that are used on the Z-bar and the clutch rod assy. It doesn't show how these things are put on in the manuals...

Some of my friends have told me the driver side would be a b&#$ to put in but it went in a total of 5 minutes as the steering column is out of the car. We moved or pushed the motor over to get the driver side in with no problems. But the passenger side is the problem. We can't push or get the...

Need some help here guys. This Old Fart is frustrated and the patience thing is at the lowest level. Putting some TTI headers in and have the drivers side in but not bolted in yet. There is no tranny installed yet. Have raised the motor about 3 to 4 inches to give me some room, but the torsion...

Can anyone tell me is there a measurement or angle the rear end suppose to be. I had pulled mine out and had it blasted and repainted when I did a complete restoration of the body. Do you just eye up and make sure the housing is 90 degrees to the ground, or does the drive shaft have to be level.

I got mine done here in Canada at C.V. Vacuum Platers Inc. in B.C. Their web site is www.cvvacuumplaters.com. Now mine I had two or three spots that were chipped on the chrome area and they charge me a little extra to repair. But when I got it back it was like brand new, better than I expected...

Thank-you very much. Now I can put it the right way before it's gets to be a hassle.

Can someone help me here. I had taken my 70 Dart Swinger ralley dash bezel apart and had it sent away to have it re-chromed and repainted. The problem is when I took it apart I forgot to mark where the Brake light indicator lens and the high beam indicator lens go. They are the tiny holes on...

Has anyone have a spare or screwed up rally dash that I can get the electrical pieces off of it. I am looking for the circuit board that is attached with a couple of screws that is behind the speedometer assembly that is green in colour. Mine has one of the three pins missing on that circuit...

Can I get some info from you experts. I had my car total torn apart to have it blasted and repainted by another person. Now that I'm putting it back together I'm missing some parts. Can anyone tell me the size of the bolts that bolt the calipers back onto the car. Are they a special size and...

Need some HELP here guys. There must be someone out there that has replaced the poly bushings on the front sway bar on a 1970 Dart Swinger or other similar cars. They are the triangular shaped bushing parts that are set inside the stock metal brackets. I have read that you can put them in hot...

Has anyone got a set or know of anyone who sells these little things. They are the covers that go onto the headliner and hold up the shoulder strap seat belt on a 1970 Dart Swinger. There are two on each side uptop of the 2 door style. I guess they just slide on and clip to the supports on the...

Was wondering if there is anywhere I could look up codes, for different components of a car. I would like to know for myself when these parts were made for my car and have it recorded for my records. Example, I have a heater blower motor that I'm about to restore and there are two lines of...

I found the same thing, as there're prices are as good if better than some. Just ordered some side marker lenses for my 70 Dart. From the order to the time I got them less than a week. I've bought a lot of goods from many different sources over the past 8-10 months and he is as good as anyone...

Hi, Like to know some info from you pros if I can, as I'm trying to get mine back to where it's suppose to be. I have a 1970 Dart Swinger 4-speed 340. I see some posts on different sizes and shapes of Z-bars for different cars, but what I like to know does the arm's that come off the tube that...

I have a 70 Dart and I replaced mine from YearOne a couple of months ago. Good price too.

I just got mine back from Just-Dashes for my 1970 Dart on Friday. Mine was cracked and faded and wanted to redo it, and they did a fantastic job in redoing one up for me. Perfect fit and colour. I couldn't ask for anything better and would recommend them to anyone.

Can someone give me some advice here. Over the years I have taken stuff on and off the car and these parts I somehow don't remember being there. I've seen in different companies that there are replacement rubber seat spacers that go under the bench seats of many cars, but I didn't have any on...