Search results for query: *

Holley Carburetor came off a ‘70 340. $60 plus shipping.

Washer and coolant reservoir from a 67 Coronet. $75 for the pair, plus shipping.

A pair of Blue sun visors, came out of a 68 Dart. $50 plus shipping. PayPal, Venmo, or money order accepted.

For Sale are these splash shield that came off a 68 Dart. $25 plus actual shipping cost. Paypal, Money Order, Venmo accepted. Thanks!

Frame Ballstud reinforcement bracket for 4-speed. See pictures below. $45 shipped in the continental U.S.

For sale is a 4 speed ballstud bracket. I believe this is for a smallblock 68-71 with the 10.5” bellhousing. $25 shipped in continental U.S.

For sale is a Hurst Competition Plus shifter. $175 to your door in the continental US. Thanks.

FOR SALE: 1968 Dodge Dart Sedan Sublime Green 1970 340 with forged crank, originally a factory replacement motor, .040 over, KB 243 Pistons, stock rods, X-heads, Comp Cams 268H, Edelbrock 7576 Intake, Quickfuel BR-67212 carb, Doug’s D453 headers, Mopar electronic voltage regulator and HEI...

So long story short, I have gone through the rebuild process and am to the point of reinstalling the main shaft/tailshaft assembly. When inserting main shaft, I can get the gap between tailshaft and main case to about 1/8 to 3/16 by hand. At that point, input and/or output shafts can be turned...

Specs are 68 Dart, 340, A833, McCleod diaphragm clutch. The car has been on the road for two summers, probably doesn't even have 500 miles on it. I'm looking for some assistance in diagnosing an issue. Approximately half way through clutch engagement I'm getting an unsettling noise. It also also...

I am looking for a black horn button and adapter for the woodgrain wheel shown in picture. Thanks!

Can I get some help matching up the correct horn button to this woodgrain wheel? I don’t know the year of the steering wheel as it came separately with the car. Thanks in advance.

These are the first plugs to come out of the new build, after about 50 miles of around town cruising. Specs: ‘70 340 .030 over X-Heads kB 243 pistons Comp 268h cam HEI Ignition Doug’s D453’s Quickfuel Brawler 650cfm Timing set at 12 initial, 32 all in Plugs are Champion RN9YC Any experienced...

The other day I noticed I had not connected the vacuum advance tube from the carb to the dizzy, must have been that way since engine breakin a few months ago. I went ahead and hooked it up, and now it seems as if electric choke isn’t operating properly on engine startup, which it was before...

What would you say the max distance the rear end could move upward towards the body would be with leaf spring suspension? The reason for the question is that I'm considering an anti-roll bar setup. Any thoughts?

Well folks, after 2-1/2 years its time to unveil my labor of love. It’s not yet 100% complete, but it’s close enough. Yesterday was the maiden voyage on the road, and it went pretty well. I want to thank this forum for it’s wealth of knowledge and help along the way, as this is my first ever car...

I'm in need of a license plate light lens for my 68 Dart? Driver quality, no cracks etc. Thanks in advance.

The wife asked me to help with the Christmas preparations:

This is my first car project and therefore first time painting. I'm pretty happy with how the paint turned out, EXCEPT, I can't get all the scratches from wet sanding removed. Everything looks nice until you catch the light at the right angle, then you can see the scratches. I wet sanded using...

I'm in the market for a pickup and would like to get some feedback from any of you that own a Ram with the 6.4 Hemi? Any help would be appreciated, thanks!

I'm getting ready to finish spraying the Dart. All that remains is the outside of the car and the decklid. Jambs, engine bay, trunk, hood, and inside of deck lid are all complete. Do I have enough paint left? I have about 3 quarts of unreduced base that will be mixed at 2:1. My math says I can...

So here is what I have. HEI Ready to Run Distributor from TSP which I purchased from PACE Performance. I have power to it(Red wire) when key is in ON and START positions. I have power to the Tach wire(Yellow) when key is in Start position. I have checked engine ground. I have ran a jumper to...

Can anyone help me identify these bucket seats?

1970 340, 4 speed, 130 tooth ring gear, 17466 mini starter the one everybody seems to use successfully. My problem is the bendix doesn’t mesh. It acts like the bendix is too big. I can engage the bendix manually, but when turning the motor by hand with the bendix engaged, it clunks really hard...

I know this is a stretch, but I'm looking for a replica Hurst baseball cap for my Dad like he used to wear in the late 70's. I've searched online, amazon, and ebay and can't find the right one. Any ideas on other places to look? I don't have a picture readily available to share, but I know I...

For sale are a pair of 340 manifolds as shown. Part #'s are 2863549 and 2863553. Heat riser does turns freely. Price is $475 plus the ride. Please PM all inquiries. For now, I'd prefer to sell them as a pair.

Is this supposed to be open as shown? 340, x heads, edelbrock intake manifold.

Here is what I have: 340, .030 over KB 243 Pistons X heads, basically stock. They are at the shop now being cleaned and checked to see what all they need, but I'm not planning on porting and polishing. Dougs headers Edelbrock air gap manifold Undecided on carb Undecided on ignition system Dana...

I am in need of a radio bezel for my '68 Dart as the previous owner installed an aftermarket radio and I'm going back to the thumb wheel. Let me know what you have, or where I might find one. Thanks!

What are some alternatives to the Edelbrock heads for my 340? Are there any in the same price range considering the whole 'bolt on out of the box theory' that I hear some many say isn't true?