Search results for query: *

Looking for a passenger side mirror that matches the remote driver's side. Driver quality preferred.

I'm changing the wiring harness in my 67 Barracuda to a M&H that is modified for electronic ignition to take advantage of a dual field alternator and the newer style voltage regulator. I was surprised to see the harness is wired for a dual ballast resistor rather than the single. I'm changing to...

I believe this is the heavy duty brake light switch. Bought it for my car before realizing I had the other one. Box has tape on it. 25.00 + 5.00 Shipping

Came with a rotating assembly from CNC, but were never used. 5M1266A ACL Aluglide Main Bearings- Std. Size CB481P Clevite 77 P Series Rod Bearings- Std. Size 50.00 + 12.00 shipping

Two sets of kickdown linkage: Bottom right is the stock setup from my 67 Barracuda 2bbl. It cleaned up nice and is mostly complete 50.00 + 10.00 shipping Upper left is 273 Commando. Bought from a reputable member here, but didn't use 50.00 + 10.00 shipping- SOLD

Unused with a little shelf wear. These came with my 24385 Hotchkis springs. 20.00 + 10.00 priority shipping

Bought it, but ended up not needing it. 35.00 from Mancini, you can have mine for 20 plus 7.00 shipping g.

Very nice and clean 1970-72 340 harmonic balancer. Sheet metal ring on rear is mint! 50.00 plus 12.00 flat rate shipping

Auto Meter 5721 Phantom Mechanical Oil Pressure Gauge, 2.3125 in. - Installed, but never run; I went with an electric gauge instead. Comes with both the stock nylon and brass lines. 40 + 8.00 shipping Auto Meter 5715 Phantom Electric Fuel Level Gauge - Installed, but only run for a short time...

Instructions state application is 67-72 a body. I bought this a couple years ago, but ended up using a QA1 bar instead. All the hardware is present, but I think I may have swapped the spacer tubes with the QA1 pieces. As always, shipping is an issue, so I'll pay half of it. Working on a box...

Made in USA. New components, not rebuilt. Single groove pulley, includes the ground wire if you're converting from the older style alternator. I had it mounted up and ran for a few minutes to test it, but I ended up with a nice date correct round back and used that instead. 100 plus shipping...

Needs cleaned up, has some black paint on it. Mounting ears look solid. There appears to be a little bit of brazing material in the bottom of the exhaust ports. Not sure why, there aren't any cracks anywhere, but the job looks professional. $150 plus shipping

For small block. P5249706, dated 4/98. 25 plus 9.00 shipping

New from Mancini. They have some shelf wear from sitting for a while. 35.00 plus 12.00 shipping.

Model A67LA. New, I didn't even take them out of the bubble wrap. 179 from Schumacher, I'll take 140 plus 15.00 shipping.

Both new in the box. Part of a rotating assembly by CNC motorsports. Pistons weigh between 679 and 681 grams with the pins. 575 obo and 25 shipping.

New M&H 67 Barracuda rear harness. I used one of their front harnesses and the quality was amazing. Asking 170 plus 15.00 shipping in a USPS medium flat rate box.

Closed chamber Edelbrock 60779 heads. They've never been fired, but may have been mounted at some point. They've been sitting bagged for years, I've had them for 2 and haven't touched them. Heads show a little shelf wear including a few superficial scratches on the mounting surfaces (2 which...

I know this has been discussed before, but I thought I'd get some fresh perspective. When I start the car, the voltmeter sits right on 13 for about 5 seconds. After that, the gauge flutters back and forth like a dog wagging it's tail. At idle, the voltage at the battery fluctuates between 13.9...

**Pending** I have a .40 over 1979 block that's fully machined, including line hone and decking. It's been bagged and coated in cosmoline as long as I've had it. I was about to be a first time engine builder, but funds dried up, and I have to let everything go. Shipping isn't really an option...

I have a .40 over 1979 block that's fully machined, including line hone and decking. It's been bagged and coated in cosmoline as long as I've had it. I was about to be a first time engine builder, but funds dried up, and I have to let everything go. Shipping isn't really an option, so pick up in...

Pioneer Diamante Series Ductless Mini-Split Air Conditioner Inverter Heat Pump Full Set with 16 Ft. Kit 12,000 BTU, 110/120V. I bought it new last summer, but never installed it. it's still boxed up in my garage. The top box was opened just to get the instructions out. I paid 850, I'm asking...

Here is the story: I bought this from a member in Florida I trusted as a fully rebuilt engine that was never fired, but not bagged properly. The heads had some rust buildup, so the plan was to remove and clean them up, then reassemble and fire the engine. Turns out the heads needed work, so I...

Looking for a rear quarter light for my 67 FB. It doesn't have to be perfect, driver quality is fine. Thanks

I'm installing Hotchkis leaf springs on my 67 Barracuda using all the supplied hardware. I expected the front hanger to be a snug fit with the eyelet on the spring, but there is a .1 gap on either side. I can easily take up the space with washers, but is that the best way forward? Maybe they...

They're in a 73 340. Do you all think they'll play well with Edelbrock 60779 heads?

Can anyone recommend a good machine shop in Central Texas? I'm willing to go to San Antonio or DFW if necessary.

Set of 4 Cragars in reasonably good condition. Car was kept inside. Rims dated 2015. Backspace is 4 1/2 or 4 1/4 if I recall correctly. Pick up in Buda, Tx, about a mile south of Austin. Unfortunately, not worth it to ship.

Original equipment just removed from my Barracuda. Worked fine when I parked the car a couple months ago. Pick it up in Buda, Tx, about a mile south of Austin. Unfortunately, not worth it to ship.

Decided on discs, so I’m selling the parts I bought to rebuild the 10" rear drum brakes on my 67 Barracuda w/ 7 1/4” rear. Drums, wheel cylinders, hoses (they sent me 2) and hardware. The hardware came from R. Ehrenberg and is speced for For all A-Bodies, 1965 thru 1972 (ONLY) with 10" X 1-3/4"...