Search results for query: *

I used a slide hammer to get the bearing out. It worked brilliantly!

Cross posting for more help. My TRW pump is off my '67 Plymouth Fury. My plan was to take the reservoir off and only replace the large reservoir o-ring, but while it was apart I noticed the circlip on the flow control valve was jammed. That's when I decided to tear the whole thing down. After...

@CudaChick1968 What color is this!?

So the boards should be 9.5 inches apart?

Let me know if your sale on the heads fall through. I’ll take a number and get in line for them

I don't think RTV had been used. I replaced the gaskets and used RTV and buttoned it back up. Have the transmission out but looking to fire it up again once I get the trans back in.

The Saga Continues... So I tried a few more things with the Pertronix Ignition. Charged my battery. Ensured it was over 12v, but for some reason I could only get 11.x at the coil. Wouldn't start. It would only burp like it wanted to start every time I let off the key from cranking. I went...

Can you explain a little more please? This is what I did to the ballast resistor. Then I connected the wires to the resistor as they were originally.

Update: Second Attempt I do believe I had my timing 180 degrees off. I took the #1 spark plug out and put my thumb over the hole and felt it blowing out. When I reached TDC on that stroke the rotor was pointed backwards. So I pulled up the distributor and spun the rotor around. I looked at...

Can't thank you enough. Really appreciate your help!!

Hopefully someone can answer this with a picture? Is it possible I need to go another tooth to clockwise?

I attempted to fire the 318 magnum for the first time on yesterday. Had a few setbacks. When I finally got around to starting it, it was dark. After it didn't start I didn't fool around too much to troubleshoot or make adjustments, but here's how it went. I primed the oil pump first. The...

This is the first time I've seen a sender like this. Could I use this sender in conjunction with my AutoMeter Z-Series electric oil pressure gauge? Would I be able to retain the use of the factory dummy light connection, and run one connection to the new Oil pressure gauge?

64-69. Apologies. I didn’t know there was a difference.

Searching for a small block 2 groove crankshaft pulley. Baltimore, MD Don't mind paying for shipping.

Two of these (One for Intake Manifold, on for water pump): Mopar Perf. Intake Manifold Bypass Fitting Adapter #MOPP4876374 One of these: Mancini Racing Intake Manifold Bypass Hose Kit #MRE4876373 Both from Mancini

Thank you sir!

I was back under the car today. Can you mount these small pumps on their side like this or do they have to sit flat?

Where can you find the shields? Going electric because I kept the factory cam and didnt want to use the cam snout bolt as I hear it has varying results. Everyone made electric fuel pump sound easy. haha. What would your drop-in tank example be? I found Holley Sniper 19-350 Sniper Diecast...

So if I mounted mine like yours, it would be on the frame above the bump stop seen in this picture? That's not below the tank though is it?

Carb'd Magnum Swap in my 1967 Fury III. Going to run a fuel pump. Can anyone show me how they have their fuel pumps hooked up and where. This is what the fuel line looks like with my head near the gas tank looking towards the front of the car. I have a Mr. Gasket 12s fuel pump.

Has anyone ever used an in-tank fuel pump in their Magnum swap? I'm going carb in my 67 Fury magnum swap. I have a small mr. gasket fuel pump to use mounted out back by the tank but I just ran across this. How much of an overkill is this? Would I need a regulator up by the carb? Holley...

Looking for a non-pitted, usable, 5.2 magnum camshaft. Located in MD.

My engine builder said while we had them out we might as well replace them, especially with over 100k miles on the engine

Edit: I started this thread looking for the wrong thing. My engine builder told me to get new roller lifers, not roller rockers. I am looking for factory replacement roller lifters for a 318 magnum. Any recommendations? Is something like part# HUG5006 what I'm looking for? Thanks!

pending sale

I'm in the middle of swapping a 5.2 magnum into my '67 fury. If I bought this package is this all I would need? Nothing additional to have the ignition system right? Mancini Racing Power Ignition Package Thanks.

I thought that might be the case but now I see SUM-G3535 for the 318

I would edit the title but can't figure out how.