Search results for query: *

OK, I've got a 340 in a '68 Cuda, Mopar electronic dist, orange box, mild cam, timing is fine, vac. is fine, don't know what my fuel pressure is, but its a stock fuel pump, and fuel lines are in the factory locations. The car starts and runs great from a cold start all they way up to about an...

Hi, anyone know where I can find the seals (they bond to the front edge of the glass and contain the window run guide) that run in the front window track for a 68 Cuda?

Check this out. 4x8 sheet of Masonite - $11.00 Trunk Carpet - $21.00 2 Cans of Spray Adhesive - $8.00

Hi, I'm looking for a complete jack set up. I have nothing, no hold down, spring (don't even know if one is needed) etc... Please let me know if you have it all including tire iron. Condition not an issue, I can restore and would prefer that way anyway (it will keep the cost down), this is not...

I've searched and searched, but can't seem to get a definitive answer, so here we go. I have a '68 Cuda Fastback, SBP, all stock suspension with a 7 1/4 rear, 14x7 all the way around, sitting on 215 70R14. I want the staggered look, so I wanted to know if 14x8 with 4.25 backspacing would fit in...

Does anyone know the A/C belt length for a 340 with A/C and the two additional pulleys, (Idler & Adjustment Pulley) It's a single belt that goes around the compressor, dampener, idler and adjuster pulley's. I'm finding a belt stating 53" but don't know if that is correct. I don't have everything...

Hi, can someone post a picture of their engine with factory A/C from a 68 Cuda (or other A-Body) as long as it has the ider pulley and tension pulley with a 318 or 340 and a single belt for the compressor. I'm not sure how the belt runs accross it, I've got idler pulley mounted correctlly, in...

I found this surfing, thought someone may need parts or a full resto, the price seems fair, it looks like its located in Westchester, NY. http://newyork.craigslist.org/wch/cto/904866945.html

I'm looking for the heater control valve for a '68 Cuda with A/C. It's the one located on the pass. inner fender with Vac lines on both side and a 90* water pipe. I don't need the bracket, just the metal diaphram unit. Pics attached.

Well, as I posted in another thread on how my Tach signal could only be picked up off the (+) side of my coil, which I knew was wrong, I did some surfing and found out that the the wires can actually be reversed without any problem, as long as all of the positives and negitives are switched...

I purchased my '68 Cuda just over a month ago. I'm going through some diagnostics on a detonation problem under medium to heavy load. Timing seems to be OK, I still need to check the total advance (I think I have too much total advance and need to adjust the vac. adv.). I'm running the MP Elect...

OK, I have installed hundreds of Tachs over the years, pretty simple actually, 3 wires (4 for lighting), one to ground, one to 12V switched, and the third (green) to the (-) side of the coil. Can someone please explain to me why I get no tach signal unless I connect it to the (+) side of the...

I've got a '68 Cuda Dash Bezel with A/C, sand blasted down to the original plastic & primed, in excellent condition. It would need a full resto paint-wise, but I'd give it an 8 out 10, maybe even a 9 out of 10. It has a 1 or 2 minor scratches, nothing to be concerned about, and was curious what...

I'm in the process of restoring the dash bezel & console in my '68 Cuda. I wanted to know your thoughts on the black and grey portions of the dash and console. Do you suggest applying the Killer Chrome to everything first, then masking off the areas that need to be black and grey respectively...

I'm looking for the 4 colored lenses for my '68 Barracuda dash bezel. I need the two green lenses, the High Beam red lens, and the Brake red lens. If no one has these, maybe you could point me towards someone who has them. I'd hate to buy a whole bezel, just for these small items. Thanks in...

Hi, I wanted to know about parts and replacing the axle shaft seals on a 7 1/4 rear. I seem to have gear oil leaking down the metal cover (held in place with 4 nuts) at the backing plate. Is there a seal in there at the outside end of the axle tube and where would you suggest purchasing these...

Hey Guys, I'm new to this forum, currently own an '06 Daytona, but got the itch for some good 'ol nostalgic Mopar. I just bought a '68 Cuda Fastback with 10" drums all around. I got my hands on a '74 Duster front-end, to do the disc conversion. So here's my question, After I install the...