Search results for query: *

SOLD!!!

My Zip is 92860 I have never used fastnall maybe you can get a quote?? Thaqnx JIM.

Sorry No, this is all I have...

Super nice rust free parts!!Will fit 1973-76 Dodge, Plymouth, Dart, Duster, Demon, Scamp and more. The door will fit from 67-76 and up just no vent window!! Doors are complete with window and latches!!$175.00 obo each. Fenders are super nice with no rust!!Driver side has a ding on top. $150.00...

Sold going to PA.

1971 Set up for Big Block!!Frame connectors,Cage,Big disc brakes,tube upper control arms,all steel with aluminum tubs,Currie 9 inch rear end$$$,Aldan coil overs,14.5x15 rear wheels with 19.5x15 tires,4x15 Fronts with Firestone skinnies,31 spline with spool,motor mounts for BB and trans mount...

Thanx Bremereric. The#6 is 3/8 and I think it's to small...JIM.

I'm thinking of maybe spraying later?????Fogger system...

Hi there guys. Running 451,fuel cell,140gph electric fuel pump,dual 450cfm Holley's and tunnel ram....What size fuel line should I run???

Very nice pictures and info..Good work!!!!

The person bought them from the one and only Dick Landy...They where NEW!! Do you guy's think it would be at least 10.5 comp ratio???"Flat top pistons"I'm hopping to run 11's on the strip ,but most street driving...

He's asking $1200 with roller rockers.........

Thanx!!! They would be on a 451 bb with flat pistons...I was informed that it was a late casting with 5 runs on them....they have the adapter plates bolted on and big valves..

found a set of BB aluminum Mopar stage 6 heads,these are in good shape"almost new" and ran low 10s in a challenger..any input???Or should I look at the Victor or eddies???Thanx for any help JIM.

Is there any one who has pictures or templates for cutting the holes to mount Hooker supercomp headers fenderwell "Big Block" in a 1971 Dart???? Thanx JIM.

Running flat tappet solid cam with 573 lift.My question is..the valve springs can handle up to 600 lift ca I go with 1.6 rockers????

Is this true???I have heard that you can run higher compression ratio with aluminum heads with the same octane fuel??????I was going to use max wedge heads"don't know the cc" But the aluminum had hart shape chambers and 72cc?????Running it on a 451 bb ..Any input???JIM.

Thanx Again JIM.

Well here we go again.... I got some Hooker Super Comp fenderwell headers..Do any one know if you need to put in reinforcement when cutting the holes??????And what about the front cross member I will be running "Engine plate or Elephant ears"????? Thanx for all input JIM.

Hi there Joe Dust.. What did you do with the power valves???Plug them or????????what secondary vacuum spring did you use????Did you use the balance tube from the front to the back carb to open the secondaries???? Thanx again JIM.

Hi there Joe Dust.. What did you do with the power valves???Plug them or???????? Thanx JIM.

Thanx for all the info...I will go with the Tunnel ram.JIM.

Do you guys think the 450's are to small?????

Here it is..... Go Tunnelram with dual Holley 450??? Or M1 and 850 dp ??????? Motor : 452 BB with iron heads max port the biggest valves you can fit,solid flat tappet roller rockers ,Msd ect.... Would like some input from the forum..Thanx JIM.

I have been all over the web LOOKING for a 1/8 mile gear calculator????Does any one know where to look???Thanx JIM.

Thanx for all the help..I will make one...

Well I'm looking for glass trunk for my 1971Dart .And a pro street aluminum wing. Thanx JIM.

Where did you buy the ProStreet wing?????Or did you make it?????COOOL CAR.

Hi there. What state are you in??I have a fresh 383 built ported heads Crower Cams Melling pump and more... MR JIM.

Well between 5500-6000 rpm