Search results for query: *

I was going to install this 5.7 into another Mopar, however things change and I am on a new path. I would like to trade: 5.7 Hemi For preferably a B motor (383/400) and if need be an RB and a transmission Other trades considered as well or good ole cash

At this time I do not wish to sell - thanks though

I have went to a TKO 5 speed and need deeper gears. I have 489 with 3:55's. I would like to trade for 410's or 430's for a 489 carrier.

I have CompCams CRB 270H-10 camshaft and lifters used on my 440. Engine made 425 HP with this in it. Engine had about 300 miles on it and broke a hyper piston skirt edge. This is a one bolt camshaft. I have the original card. I have a new dual roller timing chain with crank gear which has...

For small or big block? For small I have a set of 1.5 Comps, installed never fired. For BB, I have a set of CraneGolds - 1.6's. Send PM with photos your set or get me on PM if theres interest.

The 360 in question

Pishta -I don't have stroker, but a new (77 I believe) 360, .60 over KB 191's, 587 heads with 2.02/ (larger exh), Edlbrock Performer, Mopar Electronic, CompCam Rollers, and Mopar Purple 527 mechanical cam. Has not been fired, sitting on my stand awaiting my Cuda AAR clone - Any interest, let me...

Try Schumachers, http://www.engine-swaps.com/, they are simple and work well

I have a never installed M1 or used 440 Torker I would like to trade for a Performer RPM or equivalant. Let me know

I have a 1968/69 GTX Six Pack fiberglass hood I would like to trade for a 71 Dart Six Pac hood. Hood is in great condition, I have pictures attached. Prefer not to do the shipping thing, open to ideas

Looking for some parts for my 71 Dart Swinger I am building and want to see if I can either trade for some or sell some of them off, so here is what I have: 1. 4 Speed 23 Spline, very good shape, was going to use on my GTX but found an 18 spline Hemi for it - see picture: $400 2. 4 Speed...

Bod, I have some 15 X 10 with a 6.5 offset Weld Drag lites would be willing to swap for these if you are intersted, wont work on your fronts but would be cool for your rears?

Yep - knew that just saw the 71 part - I feel stupid

Kyle, I have a 71 fender for a Demon\Dart that I bought off Ebay as a "no rsut" part. Well people on Ebay lie, it had rust. I blasted it and cut the rust part out, just have not gotten around to finishing it up. A little work it would be an ok piece, would rather sell it, looking for $125 or...

Email sent:

Well, Finally had the 451 completed and sitting in my garage: Icons Eagles Mp 509 452's And some bitchin valve covers!!

More photos This is a good driver and a very good start for whatever. Blemishis I see are: 1. Dash pad is cracked 6. Engine bay & trunk need paint 2. Needs windshield 7. Door locks rattle 3. headliner has a small rip about 3 inches 4...

OK, Here are some photos: Again, needs to be cleaned

No problem - nice buy, good luck. Here are some updated photos, needs to be cleaned though.

I am out of town till Monday the December 19th, 2011. When I get beack, I will post some better pictures. Do you have anyting specific? Let me know.

$7,800 -

I am looking to sell or trade my 1971 Demon. It has a 318 with about 2500 miles, .35 over, stage II cam, headers, edelbrock Performer and MP electronic ignition. I believe the engine is original, but have not checked (wasn't to worried about it) I have put LBP front disks from a 73 and a LBP...