Search results for query: *

$140 total. PayPal email: [email protected] Ph: 991-734-8466

Cleaned it out. Try again.

As I said, I have 2. Both are 2463252 which are 65's. They can be redrilled so the bolt hole angle matches. Lemme know as I'll be gone for several weeks. Will return around the 5th or 6th of Oct. Make me an offer and I'll try to figure the shipping

I'll check #'s tomorrow. I have 2 of the 2bbls.

They are

Sorry I've not gotten back to you. If you still have it, I'll let you know something after the holidays. Right now I'm stretched and looking at other options.

Working?

I'm looking for a stock radio and bezel, preferably working, that I can have modified to play MP3's. Please let me know what you have shipped to 38049. Thanks

Brewer is a 4 speed guy but may have something for you. Otherwise, I'd try some of the yards in the dry west. Someone on here or ForBbodiesonly should certainly have something to suit your needs.

Nothin wrong with the ball and trunnion. Its extremely strong if in decent condition. I used a VW boot to replace the torn one on mine and it's lasted for years. Just my 2 cents. Also, the pushbutton shifter is extremely fast and accurate if it's set up properly.

I'm looking for the stock 64-66 slant 6 z-bar. zip is 38049 to figure shipping. Reasonable prices please.

I'm looking for 1 or 2 7.25 axle retainers for an early A body. These are the plates that go on the axle before the bearing is pressed on. Anyone??

Mine is a '65 and doesn't have the threaded deals on the sides of the carrier. Even if it's a blown rear, the spacers/bushings should be fine. I've been trying to get this unit together for some time. Finally found a posi unit for it and just have to assemble.

I'm in need of a .254 differential spacer for the ring gear side and an assortment of others for the other side. Any one?

I'll bet yoou can find something that'll work at Lowes or Home Depot in their hardware bins. At least until you find an actual MOPAR part It's nothing more than a pin with a press on cap like the old wagons used years ago. They still have that kind of stuff.

yeppers. Mine came out with a bunch of spider teeth. I need the section held in the center that has the ring gear and spider gears. Still a chunk -- just goes in a little differently. So what do you have?

Needing a center chunk from a 3:23 7.5" rear reasonable. I'm just outside Memphis, TN. Can anyone help?

I snapped somethin in my rear this weekend and had to leave town on business for a few weeks. When I get back, I'm going to pull the cover off and see what kind of damage I have. Thought I'd see what parts were available. I don't want or need a full housing but know shipping on parts is much...

I could use the "guts" for a 7 1/4. I think I snapped my pinion gear this sat. night and haven't had time to pull the cover. Had to leave on business for a week sun. morning. Would like to line up some options during the week and think that shipping ring, pinion and spiders would be cheaper...

x4

you can still get them at any parts store

Something to think about. The inside diamater changes along the tube and my fabrication skills aren't that good. If all else fails, I may have to go that route. Thanks

I'm looking for a Z-bar for a V-8 64-66 A body. As sometimes beggars can't be choosey, I'll also consider a /6 Z-bar in good shape that I can cut and weld. The one I had went tits up with a stock clutch. It was form a /6 that I cut and welded. Please quote a reasonable price shipped to 38049.

I'm using the stock 9.5" bellhousing for '65 273. You have a bracket??

In need of a clutch ball stud bracket that mounts to the bellhousing. I'm in the middle of a /6 to V-8 conversion and the /6 bracket doesn't work on the V-8 housing. This is for a '65 Barracuda small block. Someone out there must have one of these!! Thanks, Harv

You can still buy them new from MoPar if they are for the 10 1/2" clutch. I think they're around $30.00. There's a part # floating around out there in one of the forums or on AllPar. There are hundreds in stock in some warehouse.

Looking for a set of bellhousing bolts & washers for an early small block. I believe '64-74 are all the same unless someone knows different. Please figure price and shipping to 38049 (Memphis, TN area). Thanks.

Did you get my PM on the matter?

Thanks Larry, I need the manual trans bellhousing stuff. Don't know if the auto bolts would work. Harv

found