Search results for query: *

I have rewired the car using an EZ wire wiring kit and want to add a the brake light indicator from the block safety switch. Just trying to understand how the bulb gets power. My thinking is: Bulb gets 12v one side and the ground goes to the switch on the block and the block also goes to...

I want to put in a anti theft device on the ground circuit of my fuel pump. Can I just get a two prong switch, and wire it in series of the ground circuit? My thinking is when it is off, the circuit won't be completed, therefore no power to pump, flip it on and circuit completed. Am I thinking...

I have rewired my car with an EZ wire kit and have added MSD ignition along with FItech EFI. Now I wired the car per EZ wire instructions, which gives me 12V on their "coil wire" in RUN and CRANK which I used to feed my MSD and FItech. The car will fire and then die when using the key...

I wanted to wire in a relay to take the load off the ignition switch, but I am not sure I understand how to wire it, due to the start vs accessories. I have an EZ wire harness and it is all wired and working fine. Here is how the ignition switch is wired, how would I introduce a relay...

I rewired my car with the EZ wire 21 circuit harness. Last night I hooked the battery up for the first time and was checking the turn signals. I used the diagram per their instructions, however all 4 lights stay on, unless you pull the hazard switch, then they go out. I also have no brake lights...

I just finished rewiring my car with the EZ wiring kit and the instructions say: connect the positive battery cable before connecting the negative cable you should check for current draw. This can be done easily with a test light connected between the negative battery post and the negative...

I'm rewiring my car with an ez wire harness and I'm having a hard time finding 8 to 10 gauge wire connectors and terminals mainly for the ignition switch. I'm not looking for anything factory just something that I can easily quick disconnect. I bought some Delphi ones but I could only find it...

I am to this point and have looked through many threads, with no real answer. I called Sean today and got it, so putting it on here to help anyone on the future. Mopar -------Ez Red -------> Ign main power (red) Yellow ----> Ign Switch start (Purple) Black -----> Accessories (Orange) Blue/brown...

What bulb socket is needed for the 73+ HVAC controls light? It's a single bulb, (I believe) but the control housing is plastic, so how does the socket gets ground? Also, is the bulb a 1895? Thanks!

I have a Denso Alternator with the denso 3 wire plug. The EZ wire has: Alternator power Alternator bypass (for use with alt over 80 amps) Alternator Excitor wire The Denso has three wires: 12V reference 12V Switched Dash light or gauge (if used) I will be using the bypass wire from...

I have a 70 Dart and got the EZ wiring 21 circuit harness. I have mounted the fuse box and have all the wires ran. I started at the rear, hooking up lights. The three wires in the rear are labeled: 1. Left/Right backup 2. Left/Right Turn 3. LEFT/Right Tail Park My question is how are the...

Input a want ad out for a horn and someone said they had a hi and lo horn. Do i need both? Mine didn't have anything. 70 dart.

MSD 82073 MSD Black Blaster SS Coil Do you need a MSD box to run this coil? I have the MSD billet distributor and Fitech Fuel injection and the Fitech is going to control the timing. Just want to be sure before I order.

I have a new blaster 2 which has a slightly higher terminal case then my old one. I just put together new Taylor wires, but I cannot get the new wire to snap into the new coil, its like it's too deep for the terminal to seat. However it will snap onto the old coil. Anyone run into this?

I have been searching for the 120 amp Toyota Denso, but cannot find a listing for it. Does anyone have a part number? I have an EZ wiring kit, Classic Auto Air AC, FiTech FI, Electric in tank pump, electric fans, and a good radio. So I was hoping to get an upgraded alternator. I am aware of the...

I am getting a new set of wires and wondering if I should go with 90 degree boots or 135 degree. I have a 340 with J heads and Doug's headers. Everything is apart but I do remember having MSD straight boots before with the old hooker headers.

My kid has a power wheel that we upgraded the motor from a 6v to a 12v recently. I upgraded all the wiring and the toggle switch to change the polarity of the dc motor (to switch from forward to reverse) failed. That switch and the push button under the gas pedal were the only thing not...

I have a trunk mounted Battery in my 70 swinger and it has been that way for years. However, it has always been sitting on a battery tray bolted to the floor with a battery hold down. I just added a plastic marine battery box to it with a lid. Do I need to "vent" the battery in anyway? If...

Hello everyone! As stated in a previous thread, I got the rebuilt 340 up and running yesterday. Despite all the hurdles, everything seems to be going well. I'm going to start tuning this week and wanted a little advice. Here is what I have 68 340 bored .040 over, MSD 6A box with their billet...

Hello Everyone, I'm having trouble with the ignition switch/starter relay. I've been working on my 70 Dart for awhile now and almost finished. The previous owner had a push button start in the car, but would shut off when the key was in the 'off' position. I saw the yellow ignition wire was...