Search results for query: *

Up for sale is a brand-new set of TTi 1 7/8" small block headers. These have never been run. They have been stored on a shelf inside a climate-controlled garage, covered in bubble wrap. They have only been taken out of the boxes and installed on the engine for mock up on an engine stand as seen...

Up for sale is a brand-new Holley Sniper 4150 Stealth EFI system in black finish. https://www.holley.com/products/fue...th_4150/sniper_efi_stealth_4150/parts/550-871 This system was purchased last year and is essentially unused. It has not had any fuel run through it. At one point it was...

No longer for sale.

For sale is a pair of Gen III, 5.7 hemi heads PN# 53021616BA with rocker arms and shafts. These fit '03-'08 hemis but please check your particular application to make sure they fit. The heads are complete including valves, springs, retainers and rocker shaft hold down bolts. Heads were given a...

For sale is a brand-new in the box Engineered Cooling Products (ECP) 22" aluminum radiator with dual electric fans, shroud and fan controller for small block a body applications. Bought this setup for my Duster but wound up having to change some things around which necessitated relocating the...

For sale is a Carter Strip Super Mechanical Fuel Pump, #M6270. The pump is used but in good condition, bolt on and go. This pump took my small block Duster into the low 12s @ 110mph so it's a pretty stout pump. Puts out between 6.9-8.1 psi depending on your combo/fuel delivery system. Comes with...

For sale is an Auto Meter Phantom external mount fuel pressure gauge, #5810. This is a mechanical pressure gauge that reads to 15 psi. Must be mounted externally unless used with an isolator. Comes with black mounting cup and fitting. See my other ads for fuel system parts, would be a good...

For sale is a never-used Holley blue electric fuel pump. This came as a kit #12-802-1. The regulator is used but in good condition. The regulator bracket and some of the mount hardware is long gone but the pump bracket and little rubber piece are still there. Pump was never mounted or had fuel...

For Sale is an Auto Meter 5" Monster tach, Auto Meter Shift Lite and MSD Soft Touch Rev Control. Parts are used but in good condition and good working order. Would like to sell as a package deal for now. Tach has some scuffs and one small ding on the bezel, other wise it is very nice...

For sale is a Hughes 10" street/strip torque converter for a 904/internal balance. This converter stalled at 3,800 rpm behind my old 340 with a .557 solid cam and single plane intake. Went 12.20 @ 110 with a 1.7 60 ft. shifted at 7,200 rpm the last time I had it down the track. This would be...

Up for sale is a set of complete 5.7 Hemi heads. I believe these are from the early '00s. Casting number is 53021616AB. There are some other part numbers on the side of the heads; 0076606411 and 53021609B left and right. Probably from a Ram or Jeep but I'm not totally sure. Heads are complete...

For sale is a 1971 340 engine block. This is for the block and main caps only, no rotating assembly, cylinder heads or valve train. I will include the windage tray. Lifter valley is painted with Glyptal to aid in oil drain back. The engine was running as recently as December of 2014. In...

For sale is a brand-new-in-the-box Proform air cleaner assembly. Drop base, 14" diameter. This is a brand new part, no run time. Mounted on top of my carb for about a minute, removed and put back in the box. Comes with new filter element and mounting hardware in two finishes, black and chrome. I...

For sale is a used MSD Soft Touch Rev control unit, #8728. Unit was working when removed from my Duster. Box is in used but good condition. Wiring harness intact, not cut, plenty of length. Does not come with any chips or mounting hardware. Switched to an MSD 6 which has a built in rev...

For sale is a new B&M shifter cable, part #80805. This is a 5' Performance cable with morse style ends. This was bought for a Pro Ratchet shifter but should fit most other B&M shifters. The cable is essentially brand new but it was installed briefly on my Duster so it has some scuffs and marks...

Up for sale is a clean pair of V8 torsion bars, #890 & 891. The numbers indicate these are for cars equipped with a 318 and no A/C, measure .850" Blasted clean and primed. Nice shape no damage. $80 shipped. PM with questions.

For sale is a set of 4 piston Wilwood Dynalite Calipers, part # 120-5094, matching Dynalite Polymatrix brake pads and AR Engineering adapters which allow these calipers to bolt to your '73- up large bolt pattern disk brake spindles in place of the heavy, factory single piston calipers. These are...

For sale here is a mostly complete front end from a '74 Duster. Included in the deal though is everything you would need to convert your 64-72 small bolt pattern car to large bolt pattern disk brakes using factory OE parts. Parts list as follows: LBP spindles with good wheel bearings...

Small block/360 3 groove crank pulley. Pulled from an '84 360 out of a Ramcharger. Blasted clean, shows pitting but this is still a good, usable part. $20 + shipping. I'm in L.I., NY, 11743. Local pickup welcome. PM here for more info.

Hughes Performance HP1580 deep aluminum pan for 727/518/46-48RE. Brand new, never bolted to a case. Comes as a kit with filter, filter extension, all gaskets and mounting hardware. This is a really nice pan, thick mounting flange, looks really well made. $175 + shipping. I'm in L.I., NY...

Your ad has been deleted by Staff - Please read the Classified Section Rules before posting again.

Up for sale is a pair of Hooker Super Comp Headers for small blocks. Headers are in OK condition, have some clearance dings and dents. There is a heat shield clamped on to the driver's side tube that is next to the starter. Have been painted with hi-temp paint. Asking $75. Parts located in...

Up for sale is an 8.75 rear housing and small bolt pattern axles. Housing is blasted clean and is in very nice shape. New perches welded on. Axles are in usable shape, bearings and adjusters are good. If you buy for my asking price, I will include a pair of 10" backing plates that have been...

Comp Cams CL20-212-2 cam and lifter kit. This is the 268H cam for LA small block engines, 273-360. Good, mild street cam. Specs as follows: Hydraulic flat tappet CRS 268H-10 Basic Operating RPM Range 1,500-5,500 Int. Dur. @ .050" Lift - 218º Ex. Dur. @ .050" Lift - 218º 268º Advertised...

For sale from my '71 Dart Swinger - power brake booster, master cylinder and pushrod with firewall bracket. Part is in good working order and in very good shape. Not show quality, but better than driver appearance. Dust boot shows some cracking but does not affect performance and will not be...

Decided to put my steel crank, 318 short block and set of '302' casting heads up for sale. Here's the specs on the short block. Block itself is a '67 casting. Steel crank, stock rods, factory flat top pistons with four valve reliefs. (Probably from a truck) Block has new freeze plugs, new...

360 parts from a mid-'80's Ram. See below. 143 tooth Flywheel, 11" clutch disc surface, approx. 14" actual disc size - $30 Oil pan - rear sump for truck app. Decent condition, crusty outside but looks OK on the inside. No baffles. With pan bolts. - $25 Motor mounts - WYSIWYG - $20 Crank...

360 flywheel from a mid-'80's Ramcharger. Looks decent, no broken teeth or severe over heating. Comes with fasteners. $30 + shipping from 11743. PM here for more info.

Up for sale is my '72 440 steel crank motor. The motor is apart and basically in the condition it was in when I bought it several years ago which is dirty. Orignally purchased for an old project which is now long gone. I'm a small block guy so time for this old big block to go down the road...