Search results for query: *

has anyone used one of these carbs or even heard of these? i see them on e-bay and their prices seem lower then other brands.

hi folks I have a holley 750 on my magnum 360 that just fouls out the plugs and runs terrible. if I turn the air/fuel mixture screws in all the way it smooths out. I didn't put a vacumm gauge on it to see my readings yet. I don't drive the car much so if its dirty could I just remove the screws...

hi folks does anyone have pic's of there location of elec. fuel pump and fram HPG1 filter? I have no room to mount these in my 68 barracuda with 2 1/2 exhaust, off set ss leaf springs. I wanted to mount them close to the tank but rear end is also an issue

hi folks since my rear end is out of the car here is my thought, mounting the mallory elec. pump and fram HPG-1 filter next to the top half the gas tank and between the upper shock mounting studs. i have a .050 thick ss plate that is 20 inches long by 4 1/2 inches wide. i drilled 2 holes for...

does anyone know if fram or someone else makes a screen filter for there hp1 cannister style filter?all i see are paper element.

hi folks i have 360/380 crate motor with a 750 holley vacum secondarys. car ran fine for about fifty miles then shut it off for an hour. started it up idles fine, starts fine but as i pressed the pedal it just stumbled in all four gears. check plugs,float level,fuel pressure,timing 15 degree's...

anyone have any pictures of there carbs sealed to the scoop? ( i.e. air pan) i'm thinking of sealing my 360 to the six pack scoop. the ones that are for sale at jegs are way to small for my application. so far i have bought a .063 thick alum. sheet and have measured the inside of the scoop at...

hi folks, i'm having a problem with a stumble starting at about 1000 rpm's to 2500 rpm it will idle great and have good acceleration untill i put a load on it. if i accelerate quickly the carb responds well and seems to be fine the carb is a holley 750 with vacumm sec. front jets are 70...

i have a proform 650 with vacumm secondarys it has a high pitch whistle when i floor it. not there under gradual acceleration.very loud only lasts for a split second. any idea's? TERRY

hi folks i have a questions about carb chokes first i have a 750 holley dual feed vacumm sec. and i have never in 4 years had to use the manual choke to start it.,and it would run very well i now have put on a 650 proform with dual feed vacumm sec. and a electric choke and the engine needs...

hi folks need some input i just replaced my holley 750 on my 360/380 magnum and i noticed the base gasket that is recommend for it actually overhangs the mopar m1 single plane manifold by about 3/8 inch on one side of the inside hole diamensions. all three of the other gasket sides are fine...

does anyone use the street series proform carburators? i bought one from this years spring fling from a fellow who felt it was to small for his 440.he felt he had about 100 miles on it. its a 650 duel feed ,single pump,vavumm secondaries. are these carbs a good investment? i plan on using it on...

hi folks i'm looking into adding a proform center section to my holley 750 dual feed single pump on my 360/380 crate engine. would i really see any large improvement on horsepower to bother? car is 68 cuda with a 4 speed and 4:10 83/4. thanks terry

hi folks i purchased a new edelbrock 2 inch off of e-bay then relized that it was to tall. has anyone ever milled down a spacer to there desired height? i would like to bring it down to 1 inch. i only paid 5 dollars for it so i can risk damaging it. this is a plastic 4 hole style for a holley...

hi folks, thought i'd get your 2 cents worth on jet sizing holley 750 cfm vacume secondaries,dual feed single pump currently 72's all four corners. car is 68 barracuda 360/380 crate engine,4 speed,4:10 rear.3350 lbs., 18 degrees intial and 34 at 3150 rpm. msd 6al box and plugs gapper at 45...

ok guys need suggestions i have a 68 barracuda that i just put a 8 3/4 with a back brace on it.looks great BUT after i installed it and lowered the car off the jack i see that the gas tank hits the brace. its about 8 inches wide and maybe 3 inches deep.the tank actually sits on the brace..i...