[FOR SALE] 2019 Gen III 6.4 Hemi

-
Status
Not open for further replies.
R

Ronald C.

Well-Known Member
Joined
Jul 18, 2018
Messages
485
Reaction score
82
Location
Blanket, TX
Rating - 100%
1   0   0
Contact seller
I have a 2019 Gen III Hemi, 19k miles

Long block

Not included in the price, but I do have a 6.1 intake and BBK 85 mm Throttle Body (DBC) if someone wanted the whole setup

$4500 OBO

06DC648F-7922-493A-8A0E-0A5B7BEC4AA2.jpeg


D5485CFD-7EEF-425A-8114-06B3ADE57473.jpeg


7798C75F-0D9A-4D83-8DFE-7FC552B2F8CA.jpeg


E2D19316-C613-4206-BEDF-C377E165B119.jpeg
 
Last edited:
Not included in the asking price, but I also have a 6.1 intake and BBK 85mm TB (DBC) I would part with if it helps.....
 
Well, I’m not really sure I know the best answer there. As I understand it, 2011 or 2012 they transitioned to a BGE block. Now that said, I think the consensus is everybody likes it better than the previous blocks. But, I can say I haven’t heard any BGE 6.4 blocks. Think this is what is used for HellCat since day one.

Does this help?
 
Hello, how much for the intake & throttle body each or together as a package ? Thanks, William.
 
William Black said:
Hello, how much for the intake & throttle body each or together as a package ? Thanks, William.
Click to expand...
Hey there, really am not to interested in selling the intake and TB unless I let go of the 6.4. If I hold on to the engine, I will likely put the intake and TB on it and use in a 74 A body build I’m doing....
 
Ronald C. said:
Hey there, really am not to interested in selling the intake and TB unless I let go of the 6.4. If I hold on to the engine, I will likely put the intake and TB on it and use in a 74 A body build I’m doing....
Click to expand...

So , how much would it take to get all the correct stuff to make it run right cost ???
 
on the front side it needs a front engine cover, water pump, pulleys, and an alternator. Topside would need to have an intake manifold and a throttlebody.

other than that it’s really going to be dependent upon what you put it in. For an old a body, it would need a standalone engine harness.

With all of that said, not very much is needed if you’re interested in doing a Gen III three Hemi swap. I am purely speculating, but I would imagine the front end accessories would probably set you back less than $300 - $400 maybe? As far as intake and wiring harness, a lot of people have went with the holly sniper set up which would probably set you back about $1500-$2000? For my build, I have been acquiring parts and pieces here and there but I am confident if I did the math, I probably do not have more than this in it excluding the cost of the engine....
 
w2dodge said:
would you sell block alone?...if so how much..?
Click to expand...
Unfortunately, I don’t think I can break it out. The engine has a limited number of miles on it. If it does not sell, I will likely pilfer a 5.7 block that I have for parts, and swap it into my a body.
 
Ronald C. said:
Unfortunately, I don’t think I can break it out. The engine has a limited number of miles on it. If it does not sell, I will likely pilfer a 5.7 block that I have for parts, and swap it into my a body.
Click to expand...
ok...I had to ask
 
Status
Not open for further replies.
-

Back
Top