440/ RB Weber manifold anybody?
- Thread starter 67Dart273
- Start date
-
Dartnut
Don't hate me because i'm beautiful
It all depends on what someone considers as ''outlandish''.
To me, the price wouldn't be too bad, but the shipping is almost 100 bucks.
That gets you to a grand total of about 425 bucks shipped to your house.
That is quite expensive for what you are getting IMHO.........
Let's hope it stays there.
diymirage
HP@idle > hondaHP@redline
OK, you post up another add for a 4x2 intake for under $350.00
(with carb linkage)
i looked at those hoses, and they connect a weldable piece to a welded piece
so that tells me they made that section removable for a reason
just because i dont see the reason at first glance means nothing
i must be closer, shipping to me is only 28.45
which puts the whole thing at 350
gzig5
Well-Known Member
only $28 shipping to my house 32 miles away. I like the idea for a prototype, then do it again so it looks good.
Guy has some interesting stuff, including a 383 six pack type intake
Offenhauser 3x2 Three Deuce Tri Power Dodge Chrysler Mopar 400 Intake Manifold | eBay
pishta
I know I'm right....
Have you priced IDF Webers? 4 big ones will set you back >>800. This will also be 2 feet tall once the carbs are installed. Smaller are cheaper, this 40 IDF is a steal!
https://www.amazon.com/Carburetor-Barrel-Volkswagen-Beetle-Porsche/dp/B07TDG1MFY/?tag=fabo03-20
EDIT: you only need 2 40's as the CFMs are about 430 a piece. and they are NOT progressive. Think of an 850 Holley double pumper with a 1:1 linkage. Hope you can feather that throttle. >>>Actually on an IR intake, you'll need 4 as they pull from one venturi only. Not the 4 of a standard common plenum intake. So an almost 8 liter motor will pull 1l per intake event through one of those carb throats. You'll need some Weber carb for that considering a 2180cc VW works great on dual 44 IDF's pilling 545CC per intake event.
https://www.amazon.com/Carburetor-Barrel-Volkswagen-Beetle-Porsche/dp/B07TDG1MFY/?tag=fabo03-20
EDIT: you only need 2 40's as the CFMs are about 430 a piece. and they are NOT progressive. Think of an 850 Holley double pumper with a 1:1 linkage. Hope you can feather that throttle. >>>Actually on an IR intake, you'll need 4 as they pull from one venturi only. Not the 4 of a standard common plenum intake. So an almost 8 liter motor will pull 1l per intake event through one of those carb throats. You'll need some Weber carb for that considering a 2180cc VW works great on dual 44 IDF's pilling 545CC per intake event.
Last edited:
gzig5
Well-Known Member
I think if you are going to run Webers, you got to let the people know. 
Must have at least $43 in rad hose there...
Hope they have the coil spring inside
Hope they have the coil spring inside
Last edited:
Hyper_pak
Old School Chrysler Fan
More like $400 EACH for carbs. And that is for the Spanish new models, not the original Italy models. So that is $1600 and tuning and linkages and fuel lines. I like it, it's cool, but not cheap.
mopar head
DoD Alien/Squatch slayer
My goodness, I`m about 1/2 blind but some of you guys are aren`t looking close.
There is just short pieces of hose connections. And rad hoses? they do make larger fuel rated hoses.
And REAL Webers would set ya back around $3500 to top that Intake off.
There is just short pieces of hose connections. And rad hoses? they do make larger fuel rated hoses.
And REAL Webers would set ya back around $3500 to top that Intake off.
kowalski440
Well-Known Member
Now tell me why that won't fit my 383 also?
diymirage
HP@idle > hondaHP@redline
Maybe that is why there is a section of hose in there, instead of welding it solid
Buy it and try it
pishta
I know I'm right....
section out an inch of that top "girdle" and youll be set. China copied Weber now so you can skimp on the carbs @ ~100/pc and totally going through them to make sure they could work. That looks pretty easy to fab if you can source those 45's or just form them on an arbor.
Tedshredz
New Member
8packMopar - 8 Pack 440 Mopar 4x 48 IDFs
here‘s something else….probably really expensive if a $350 project piece is too much from eBay.
here‘s something else….probably really expensive if a $350 project piece is too much from eBay.
well i've got this setup , but have you looked at bbchevy intakes , i've been told that port and bolt patterns are the same . just need to cut off the valley tray and build one for the rb block .
MomsDuster
Well-Known Member
Don’t know how that would perform, but damn that looks cool!
i've also found that sbchevy and sbmopars have the same port n bolt patterns , who would have thought this ? here is adapters to put a chey sb intake on a mopar sb
LOL!!! Yeah, like almost 100% of the new vehicles built for the last 25yrs are running around with that "rad hose", filler neck to tank....
........
jbc426
Well-Known Member
I have access to a complete set of authentic, high-flow, tunable runners for that intake available for only $500, but that also includes all-new hygear hose clamps. Shipping is extra, and drop ships from Oriely's auto parts.
-
