[Found!] Head Pipes

[fatandgreazy]

Anybody know where I could get a set of stock 17/8 head pipes for a 1969 valiant with a 340?
Thanks

 

[HemiSSDart]

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

 

[pishta]

(see option box below) -A-Body 318-340 and 360 Head pipes (P

 

[fatandgreazy]

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

You would have to specify a 70-71 Duster 340 Classic Industries, AccurateLTD, Gardner Exhaust...

OK I will give them a call tomorrow..Thanks

 

[fatandgreazy]

(see option box below) -A-Body 318-340 and 360 Head pipes (P

(see option box below) -A-Body 318-340 and 360 Head pipes (P

I checked out ACCURATE EXHAUST before all I need is the head pipes they won't separate.

 

[jazak5]

tti nice and hd

 

[RustyRatRod]

I checked out ACCURATE EXHAUST before all I need is the head pipes they won't separate.

Your local muffler shop can make some I bet.

 

[Ironracer]

Your local muffler shop can make some I bet.

Absolutely! For most my cars, I usually take a framing square, a tape, and a speed square, write down the numbers, and roll. DISCLAIMER: great for headers back...I would not try to do the over axle and out that way. Jes sayin!. However, if'n I pull my head out my ***, I may take the 2" rears up off my car n take em up and have em duplicated in 2.5".

 

[fatandgreazy]

I have a set of factory pipes from manifolds to mufflers. From a 70 duster. Kim

A

I have a set of factory pipes from manifolds to mufflers. From a 70 duster. Kim

Are they 1 7/8"?

 

[fatandgreazy]

The drivers side necks down to go past the torsion bar. I think it’s 2 inch there, then as soon as it’s under the car it’s 2 1/4 to the muffler. The passenger side is 2 1/4 right off the manifold I believe. I can measure them next time I’m out at my storage. Kim

Thanks Send me a PM with the Info.

 

[Oldmanmopar]

I have two sets from a 70 Duster. One set new and one set slightly used. Slightly used set is $75 plus shipping. I also have the tail pipes for tips. $20 each used tips for them ad $85. Complete exhaust minus mufflers $200.

Complete new sticker exhaust with mufflers $500 plus ride.

 

[fatandgreazy]

I have two sets from a 70 Duster. One set new and one set slightly used. Slightly used set is $75 plus shipping. I also have the tail pipes for tips. $20 each used tips for them ad $85. Complete exhaust minus mufflers $200.

Complete new sticker exhaust with mufflers $500 plus ride.

I have two sets from a 70 Duster. One set new and one set slightly used. Slightly used set is $75 plus shipping. I also have the tail pipes for tips. $20 each used tips for them ad $85. Complete exhaust minus mufflers $200.

Complete new sticker exhaust with mufflers $500 plus ride.

PM sent

 

[fatandgreazy]

PM sent

Still Looking.

 

[Oldmanmopar]

I sold the complete Exhaust. You only wanted the front pipes and another member bought the whole new exhaust. Front pipes , mufflers, hangers, tailpipes, tips and tip hangers. I only have the used set left and need to keep one of the exhausts for a car that is here.

 

[fatandgreazy]

I sold the complete Exhaust. You only wanted the front pipes and another member bought the whole new exhaust. Front pipes , mufflers, hangers, tailpipes, tips and tip hangers. I only have the used set left and need to keep one of the exhausts for a car that is here.

I sold the complete Exhaust. You only wanted the front pipes and another member bought the whole new exhaust. Front pipes , mufflers, hangers, tailpipes, tips and tip hangers. I only have the used set left and need to keep one of the exhausts for a car that is here.

OK Thanks for the update.

 

[rlcbit]

I can bend them would be 2’’ OD. I think i have the card for 340. I bend all my big block darts.

 

[fatandgreazy]

I can bend them would be 2’’ OD. I think i have the card for 340. I bend all my big block darts.

View attachment 1715869964

View attachment 1715869965

View attachment 1715869966

View attachment 1715869967

Thanks for the reply but I really need the stock 1/78" pipe from 70 duster room is a problem.

 

[oldkimmer]

One more time the front pipes are NOT 1 7/8. Drivers side is 2 inch then goes to 2 1/4. The passenger side is 2 1/4 right off the manifold. Get the pipes from oldmanmopar. He still has the used set. Kim. Pics. First 2 are the drivers side with the indent for the torsion bar, then to show the 2 1/4 over the 2 in pipe. Then the middle pipe is the pass side showing 2 1/4 right off the flange all the way to the muffler.

 

[rlcbit]

I don’t have 1 7/8 dies

 

[oldkimmer]

The drivers side is 2 inch for about 18 inches. I would have to measure. Then 2 1/4 to the muffler. Idk how he got 1 7/8s. Pass side is 2 1/4 all the way. Here is a pic of the drivers side. The pipe is flattened some to go past the T bar. Then 2 1/4 after that. The pipes are also flattened on the bottom in a couple of places. Pass pipe pic in the middle. Other pipe is 71 up Walker brand. Kim

 

[jsjs1212]

The drivers side is 2 inch for about 18 inches. I would have to measure. Then 2 1/4 to the muffler. Idk how he got 1 7/8s. Pass side is 2 1/4 all the way. Here is a pic of the drivers side. The pipe is flattened some to go past the T bar. Then 2 1/4 after that. The pipes are also flattened on the bottom in a couple of places. Pass pipe pic in the middle. Other pipe is 71 up Walker brand. Kim

View attachment 1715870553

View attachment 1715870554

View attachment 1715870561

View attachment 1715870562

View attachment 1715870563

Hi,
Contact Dons exhaust Canton Ohio. He has what you want. Google it.

 

[fatandgreazy]

Thanks, I will check them out tomorrow.

 

[moparmandan]

I have TTI and Accurate head pipes available (I would separate the Accurate) but they are 318 ball and socket not 340 flange.