Wideband O2

-
340inabbody

340inabbody

FABO Gold Member
FABO Gold Member
Joined
Jan 31, 2018
Messages
850
Reaction score
428
Location
Arizona
Guys has anyone installed a Wide Band O2 bung on a long tube header collector while connected up? Let’s assume I have a decent 360 angle to weld it. I really don’t want to yank the heads if I don’t have to. Just curious if this is a common practice or a definite no no.

Thanks
 
Last edited:
340inabbody said:
Guys has anyone installed a Wide Band O2 bung on a long tube header collector while connected up? Let’s assume I have a decent 360 angle to weld it. I really don’t want to yank the heads if I don’t have to. Just curious if this is a common practice or a definite no no.

Thanks
Click to expand...
Yes just disconnect your battery and you can weld them on the car with out hurting anything besides burning something while welding of course.
 
That's what I did. I did lose the sensor after a couple years. My buddy said I should have went back more due to heat but IDK.
 
340inabbody said:
Guys has anyone installed a Wide Band O2 bung on a long tube header collector while connected up? Let’s assume I have a decent 360 angle to weld it. I really don’t want to yank the heads if I don’t have to. Just curious if this is a common practice or a definite no no.

Thanks
Click to expand...
Yes. I've done it twice on two separate cars. Both work great. Take care on how the sensor is positioned. The plug end part must have a little upward angle to avoid water pooling into the actual sensor part (part that is actually into the exhaust stream). Wire it up and tune away!!
 
85glht said:
Interesting... Leaded gas kills these things... not sure why you "killed" one so quick... maybe it was faulty
Click to expand...


A big killer of the sensor can be using silicone that isn’t O2 sensor safe.

IIRC , Permatex says if it’s automotive and their name is on it it’s sensor safe.

If you are buying silicone at a hardware store or similar it’s probably not sensor safe.
 
Newbomb Turk said:
A big killer of the sensor can be using silicone that isn’t O2 sensor safe.

IIRC , Permatex says if it’s automotive and their name is on it it’s sensor safe.

If you are buying silicone at a hardware store or similar it’s probably not sensor safe.
Click to expand...
That too!!!
 
Mims Gt said:
Should be in the collector half wayish depending on interference possiiblity and optimal @ 3 oclock or 6 oclock position .
Click to expand...
6 o'clock? If you're talking about on the bottom, that is a hard NO! Never want the sensor to lay where condensation may collect. Now basically ANY position except 6.

I welded mine in the passenger side of my TTI's at about 9 oclock, looking into the header. No prob. 15 minutes.
 
i never used any silicone. A little anti seize on the last few threads is ll you need.
 
Ironmike said:
i never used any silicone. A little anti seize on the last few threads is ll you need.
Click to expand...


I mean non sensor safe silicone ANYWHERE on the engine.

It will kill the sensors lickety split. If there is non sensor safe silicone anywhere on the engine it will kill the sensors.
 
I’ve done a couple installed a t about horizontal. I have it plugged into my Innovate LM1 for tuning the carb. It’s a temp setup with the cable running out the window. It’s a great tool.
 
Ironmike said:
6 o'clock? If you're talking about on the bottom, that is a hard NO! Never want the sensor to lay where condensation may collect. Now basically ANY position except 6.

I welded mine in the passenger side of my TTI's at about 9 oclock, looking into the header. No prob. 15 minutes.
Click to expand...
yeah sorry meant 9
 
Rich kills them too. They diagram how the sensor should be located.
 
1MeanA said:
I’ve done a couple installed a t about horizontal. I have it plugged into my Innovate LM1 for tuning the carb. It’s a temp setup with the cable running out the window. It’s a great tool.
Click to expand...
Yeah I have the LM1 as well. Originally for the tail-pipe but I didn’t think that was a very accurate way to measure.
 
340inabbody said:
Yeah I have the LM1 as well. Originally for the tail-pipe but I didn’t think that was a very accurate way to measure.
Click to expand...
I have the tail pipe clamp but I don't like to use it. It doesn't work well at idle plus I would need a very long cable.
 
You must log in or register to reply here.
-

Back
Top