72 duster resto

-
Had a full saturday morning to work on the car so got a few more things wrapped up:
  • 8.8 backing plates, emergency brake, rotors, pads, calipers all installed
  • painted up some more engine bay
  • testing out some variant of flat black engine paint on my valve covers, but not sure I like the idea of keeping them clean! lol.
I also thought it would be cool to paint the covers with F3 sherwood and then touch up the lettering with orange, but that sounds like a project for later.

On the engine Brian said it's not a big deal with adjustable rockers so just gonna install the valvetrain, spec the pushrod lengths, grab the right set and make sure the pushrod ports in the heads don't need any clearancing before I torque everything down. I'm stuck waiting on a lost set of arp headbolt washers that probably got lost when I last cleaned up my workarea. Hate that. Oh well. Grabbed some gear oil for the rear end so nothing stopping me from setting pinion angle and welding on the spring perches next. Can't wait to drive this thing.

I do have one question - for those who have converted column shifts to floor shifts is this an easy task? I dont NEED to do it (yet), but I was reading the instructions on my Summit brand header installation and it mentions potentially reconfiguring the shift linkage if clearance is an issue. I knew header installation would be a PITA at some point but trying to get ahead of any headaches down the way if possible.

Screenshot 2024-08-26 at 10.02.41 AM.png


Screenshot 2024-08-26 at 10.02.25 AM.png


Screenshot 2024-08-26 at 10.02.19 AM.png


Screenshot 2024-08-26 at 10.02.11 AM.png


Screenshot 2024-08-26 at 10.02.06 AM.png


Screenshot 2024-08-26 at 10.02.00 AM.png


Screenshot 2024-08-26 at 10.01.55 AM.png


Screenshot 2024-08-26 at 10.01.51 AM.png


Screenshot 2024-08-26 at 10.01.47 AM.png


Screenshot 2024-08-26 at 10.01.41 AM.png
 
Todays progress. Gettin the kids to work.
Got a pushrod measurement of 7.3” - closest ones I see are 7.342 ill order. Also waiting on a hughes order for some shims for the arms

IMG_8483.jpeg


IMG_8482.jpeg


IMG_8478.jpeg


IMG_8451.jpeg


IMG_8450.jpeg
 
Hughes spacers for my rocker arms… wont be buying from the again. Came in a bag that could easily have been oiled to prevent rust. But a little elbow grease and theyll work.

Got the rocker arms installed and prepping my checklist for wrapping up the block. Hopefully ill be dropping the engine back in the car this month.
IMG_8706.jpeg


image.jpg
 
Last edited:
Anyone know if there are “longer than stock” adjuster ball screws for 273 rocker arms? Ran out of thread length getting preload on a few valves
 
Things have been slow around here. Busted a finger doing a brake job on my wife's minivan... woof.

Anyway, Nothin' like straddling separate projects. It's the best way to get something done while waiting for parts to ship for another. So while I have pushrods on order, I finally welded up the spring perches on the 8.8 @ ~7degrees pinion angle. I will fine tune the angle once its installed. If you do this project, definitely pull EVERYTHING from the junkyard and don't buy it bare. I am still hunting vent tubes and brake line clips to put all the parts together. Just to get the 8.8 out of the way i'll probably install it and do the rest of the job under the car but man it would be nice to be done already! haha.

More updates to come.

Screenshot 2024-10-21 at 11.02.37 AM.png


Screenshot 2024-10-21 at 11.11.31 AM.png


Screenshot 2024-10-21 at 11.12.17 AM.png
 
72smallairparticler said:
If you do this project, definitely pull EVERYTHING from the junkyard and don't buy it bare. I am still hunting vent tubes and brake line clips to put all the parts together.
Click to expand...
rule number one: take everything at the yard. the bits n' bobs, pins, clips, whatzits, doohickies, dongles, dangles, nuts, bolts, washers, ALL of it.

you don't need it? it goes in the "spares" can to be relegated to the land of misfit hardware-- or as i like to call it: the island of last resorts.

when you need it, it's gold; till then, it's junk.
 
Just found this build. Very nice progress! Any chance you know the weight difference between the 7.25 and the 8.8?
 
bjkadron said:
Just found this build. Very nice progress! Any chance you know the weight difference between the 7.25 and the 8.8?
Click to expand...
Ahh shoot no I dont actually. Id weigh them both but I just sold the axles from the 7.25” the 8.8 is definitely heavier but cant say how much
 
You must log in or register to reply here.
-

Back
Top