Search results for query: *

Have a blower motor out of a 68 barracuda, it has been bench tested and it does spin freely. It is missing one of the ends on the wiring and here are the part numbers on it 3441 409 42166 1931. I am asking $35 plus shipping from 61469 Illinois.

I am looking for the motor mounts for a 340 that's going into a 72 dart. I am willing to use the 318 mounts if necessary as the 340 ones are hard to find plus a little cashy. Please post pictures and price shipped to 61469 illinois. Thanks

I am sure this has been asked before but what is the correct orientation for the motor mounts on a 340, picture 1 or picture 2 this for an a body.

Have a set of a body sm blk headers that were used for break in on a run stand only. I am not sure of the brand the only info I could find was the number 4200 on them. I do not know if they are stainless or coated. The collectors will be included and I am asking $175 plus shipping from 61469...

Heater box j hook a body not sure what all years it fits. I am asking $10 plus shipping

I did read an older post on this but still a little unclear on my problem. I did a front disc conversion, have all new lines, master cyclinder, proportioning valve, t -block ect. I get a good stream out of the front but little at the rear, there is fluid. I did break the line loose at the rubber...

Have a chrome moroso deep pan for small block 318-340 up for sale. This was used for break in on my 340 and from research I believe that the part number is 1957? It would need the 24700 pickup tube. It does have a repair on the bottom (don't ask stupid mistake) but does not leak and a couple of...

I am looking for a oil pan, windage tray with the 4 small bolts and pickup tube for my 340 going in a 72 dart. I am really hoping someone has all of this for a one shop deal. Please provide price shipped to 61469 illinois along with pictures. Thanks

Have a chrome Mr gasket duel feed fuel line part no 1554 for Holley 4011 series carbs. It is a 3/8 line and 8 3/8 center to center. I am asking 20 plus shipping from 61469 Illinois

I have a chrome throttle bracket that was on a 383 that was in my dart when I bought it, not sure what all it fits. I am looking for 65 shipped from 61469 obro. Did some research and this is for b and e body only

Have a pair of anco wiper arms I don't need, one arm has 15a on it and the other one just has a on it. I am asking 15 plus shipping from 61469 Illinois

Have a 1 in carb spacer asking 15 plus shipping from 61469 Illinois

I have a pair of stamped steel moroso sm blk valve covers. These are driver quality with some rust spots and light scratches on them. I am asking 35 plus shipping from 61469 Illinois obro.

I have a new amd 70-72 dodge dart rear valance for sale that I did not use. I am asking $275 obro plus shipping from 61469 illinois

1) which location is better for the mechanical gauge lines, the factory sending unit location or coming off of the adapter? 2) I currently have the plastic line but would rather use copper at least up to the firewall and then plastic into the gauge. what size copper tubing would I need? Thanks

I am sure there has been questions on this before but, I bought the 3 3/4 in ground strap but it is not long enough to attach from the fuel line to the sending unit. My question is will it do the job if I attach it to the return line and the return line port on the sending unit?

I am needing the reverse wire harness for a 833 trans. This is the 2 prong plug or a source to get one. I am doing a 4sp conversion in my 72 dart and do not have this. Pictures and price shipped to 61469 illinois if anyone has it. Thanks

Ok, I have my shifter clamped in my vice to check all of the lever functions after rebuilding it but I am puzzled on the reverse function. When I try to shift it into reverse the 1-2 lever is moving also, the reverse lever does move back like it should but the 1-2 lever has me concerned, is it...

Ok I have a 72 dart swinger and I bought new parking brake cables from inline tube. I have the rear cables assembled but I am at a loss on the front cable routing. The old cable is still in place but I can't see anyway possible to run it the same route as the original. So is there an alternate...

I am wanting to know if this is the correct location for the return line on my 72 dart. This is what I ordered from inline tube, it just looks too far forward to me and does it attach to inner fender someway? Thanks

I need to know what to do on my locking pawl alignment. The one on the passenger side (right side) is fine but the drivers side (right side which is the adjustment side for backlash) is off quite a bit. I have the backlash right at .008.

I am looking for the unicorn, I need the drivers side reverse light lense and the passenger side tail light lense in the 71 stainless trim style. Please post pictures and price shipped to 61469 illinois. Thanks

Have some extra parts i don't need, prices are plus shipping. Alternator pulleys $10 each 2 5 /8 pulley SOLD big blk (out of a 383) oil pump drive $15 sm blk dist. hold down $5 cam thrust, eccentric and washer no bolt $15 SOLD rear view mirror bases wire wheeled clean up $10 ea

I am looking for the glove box and trunk light switches for a 72 dart. Thanks

What size of screws do the fuel fill tube trunk seal and fill neck to fender take for a 72 dart, I seemed to have lost mine. Thanks

Have some chrome lug nuts to get rid of driver quality with some polishing. 10 -1/2 x 20 rh with 3/4 in length and .68 wide shank 10 -7/16 x 20 rh with 3/4 in length and .68 wide shank 9 - 7/16 x 20 rh with 3/4 in length and .68 wide shank I am asking $15 per set plus shipping from 61469...

ok guys, I need some direction on rear tire to fender clearance on my 72 dart other than different rims with a deeper offset (not in the budget). I have 235/60/15 tires mounted on cragar ss 15x8 with 3.5 in offset, I just put air shocks on as regular shocks didn't work and even with 110-120 lbs...

I am attempting to check the functions of all my electrical components prior to installing the motor in my 72 dart. I have all new m&h wiring harnesses through out the entire car. I put the battery in connected the red power wire from the bulkhead and a power wire from the battery to the...

Have a new amd rear valance for 70-72 darts. I am looking for $325 shipped in the lower 48. These are right at 400 plus taxes and shipping from amd.

I have a set of sbp slots. The fronts are 14x6 and are Fenton drag rims. The rears are 14x7 (not sure of make) and have been drllied for screws. I believe that I also have a complete set of 7/16 lugs and washers for them but will need to check. I am asking $125 plus shipping from 61469...