Search results for query: *

well.... no more oil leak. I changed valve cover gaskets, replaced the oil filter and potted the inside of the oil dipstick with epoxy. So, one or a combination of those items were the culprit. I would bet on the valve cover gaskets.....

I have not had the car out. I hope to take it out this coming weekend.

did you determine where it was actually leaking?

good question..... manual steering car so I eliminated that. Transmission cooler up front, but no oil in that area or on the fan. I am replacing the valve cover gaskets, fuel pump block off gasket, and a new oil filter.... Then, it will have to wait until spring because my full throttle...

wow.... interesting. I will definitely look at that area. Thanks

hhhmmmm oil filter.. good suggestion. I need to look low. I have been focusing up high. Thanks

I am running electric pump. I am going to replace the gasket on the block-off plate. This has me scratching my head.....

I need some fresh ideas. After a 1/4 mile pass, I am getting motor oil on the passenger side inner fender and underneath the hood. I have ruled out the valve cover breathers and the dip stick. Valve cover gaskets looked good. It appears to be from the passenger side. Has anyone experienced...

AWESOME..... thanks everyone.

woops.... it is a 67 Dart with a 360. I have an aftermarket Alum radiator, but the inlet is close to the stock location. I don't want to run a flex hose and I have seen small block A Bodies with new molded radiator hoses. I just can't find one???? Thanks again.

Help..... I can't find an upper radiator for a small block A Body. Can someone help? A brand and part number would be awesome! Thanks

I have entered my 67 Dart into an on-line car show for 105.7 MAJIC (Cleveland). The winner is chosen by on-line voting. You can vote once every day. HELP out the MOPAR.... thanks. http://www.wmji.com/pages/contests/mark-nolan-online-classic-car-show/

I decided on an old style hemi scoop. However, you are the one that has to like what ever you choose.

what would you want for everything? is it from a 67?

I need the piece that goes along the top of the finish panel. I gave up on finding a cheap finish panel, no such thing. It would be great if you have the trim. Thanks

Hello.... I am in need of trunk moulding for a 67 Dart.... can you help????

I am in need of a trunk lid and trunk trim for a 67 dart. can you help?

Well, thanks to a tree limb, I need a trunk lid and the trunk trim for a 1967 Dodge Dart. Can you help me???? Does anyone make a fiberglass trunk lid???

i bought stuff from YearOne. Make sure that the clips are in place BEFORE putting the windshield in.

probably hard to find.. however, figured I would give it a shot. All for a 67 Dart. 1.. inner fender splash shields (goes in front of the doors inside the fenders) 2.. "DART" letters for the rear quarters. 3.. Rear trunk emblem "DART GT" 4.. hood and trunk letters. Help????

Hello... I purchased a pair of splash panels (2 years ago) and they dont fit my 67. The best i can figure is that they are for a 70 and newer a-body. I can buy ones new, but I dont want to spend $200. Does anybody have a used set???? Thanks

I need some pictures or good instructions on how the headliner trim pieces that run along the sides is actually held in place? are there clips??? etc. help

i have a bracket from a 67 . will that help you?

awesome.... let me know.....

Hi all... I am in need of the door handle rod between the door handle and the door latch. I need both drivers and passangers side. Please respond with cost and shipping to 44089?? (This is for a 67 Dart) MANY THANKS......

thanks.... the part numbers are a huge help.

outright AWESOME.... thanks much.

any thoughts / suggestions on how best to protect the starter wiring from header heat????

which transmission speedometer gear will be close for a 904, 4:10 gears and 26 in diameter tires? Thanks.

i need a finish panel for my 67