Search results for query: *

also some pedal assemblies use plastic bushings and the HD units use bearings.

The jeeps have an overdrive transmission so most of the jeeps have 3.55 or numerically higher gear ratios. Really check your local salvage yard good for a rear end. I went to my local salvage yard and asked if they had an 8 1/4 out of an Abody and they said no we havent had one for years, as a...

That is my same reason for considering one also. Control freak IFS has a front suspension system for the a bodies also.

Do you still have the spare tire drop?

i used to paint with no mask, it caught up to me and i was coughing blood for a couple days, its already bad enough that i smoke! but your fast back is looking great

Im located in annapolis MD not too far away from NJ. Im interested in your disc brake parts k frame and lower control arms with sway bar, and the upper control arms. If i drive up there could you give me a deal on the parts? Any way please send pics to my email, [email protected] what...

are those spindles based on a body height or are they the 3/8" taller f body units?

why would the steering column affect the centerlink/pitman arm/idler arm

For my 8 1/4 Im planinning on getting a 29 spline suregrip and 3.73 ring and pinion from a jeep cherokee along with the rear disc brakes and then get custom axles built in 29 spline and stock a body length, Im tryin to build a gorilla 8 1/4 lol. also planning on a rear end cover that supports...

does it make a difference if you remove the brake assembly off of a jeep with a dana 35 rear axle or does the jeep have to have an 8 1/4? there were two rear axles optional in the 1994 through 1998 jeep cherokees, dana 35 and 8 1/4

I installed an 8 1/4 in my 1967 barracuda fastback and im planning on doing this swap also. Do the emergency brake hardware from the jeep work with the 8 1/4 a body rear? Did you have to weld a mount on the housing for the caliper hoses? Thanks man!

Hello, I'm Tony, I'll be turning 18 in december(next month!). Right now Im working on a 1967 Barracuda Fastback that i bought about 3 or four months ago with all the money i earned delivering pizza with my little VW that i bought in January 2009 with saved up money. My Dad got me into mopars...

what about 1 7/8 hedman huslers with 3.5" collector that runs into a 2.5" full exhaust in an abody with a 360

does anybody have pics of the hedman 1 7/8 installed?

does this coil over kit improve handeling? is it better than thicker torsion bars

what other coil over conversion kits are there that dont require you to spend 5k on a new k member to lose your torsion bars?

did u ever think about using a dakota 5 speed? i think that the only problem would performance accesories

i was just wondering, will a 5 speed from a 1990's dakota work with a small block without using a bellhousing adapter

that looks like a cast crank, was the harmonic balancer thick? if it was then its a cast iron crank whatever it is, your lucky because the crankshaft is drilled for a manual trans

Will a stock converter work in a reverse pattern race 727?

No i havent called lenny, im pretty much set on a manual trans. I just hope the 727 isnt hurt & its just the converter that went bad

the outer input shaft of the transmission wiggles a tiny bit though, i dont know if this is normal or not because im no trans expert.

Ok i removed the transmission and to my surprise the fluid inside was perfectly clean & there wasnt any bits of metal in the pan, The converter looks clean too.

thx for the posts, i found out through trial & error i have my turn signals wired custom

im trying to figure this out too...

is that a viper t56? looks awesome

Thanks so much!

FYI im using fenderwell headers How do i determine how much length i have to cut off the input shaft? also what kind of welder do you recomend to weld in the floor hump & frame plate that the clutch linkage bolts too? thanks everyone

thanks alot for all the great posts!

my 1970 dodge dart that i got recently. i found an aluminum 10.5" bellhousing for $350 o.b.o. i was just wondering if an aluminum bellhousing is streetable & strong