Search results for query: *

Cummins 5.9 weighs a grand if it weighs a pound. Probly closer to 1200

Doubt that frankly. Headlights are grounded up front on the rad support. I'd bet the trouble is right in the cluster area

Think maybe you FOUND it!!

What engine is this? Are you sure the HDK stuff is up to the task of that boat anchor of an engine?

This certainly sounds like a grounding problem. The cluster is poorly grounded by the mounting bolts to the dash frame, and the PC board is grounded to that by it's mounting screws. Find a common ground on the PC board and install a pigtail, then bolt the pigtail to either the column...

This was an eviction some years back, up the street. A real bunch of idiots. Loose dogs, lots of junk cars a constant stream of people and animals. This was taken from Bing maps This duplex now has two good families living in.

What is "2v at the fuse?" Fuse link up by the starter relay? You have likely found it, either the link is AFU internally, corrosion, etc, or a bad connection right there such as the eyelet terminal on the relay end of the fuse link Also you must be careful evaluating and taking...

I wish them the best. I had to lock up all 4 on the 04 GMC today going down a 25mph street, some **** pulled RIGHT OUT. I stopped about 4ft from him and sat there with the finger. Sunny day, dry streets, NO reason he did not see me.

No

If you still use an ignition system with a ballast, there is no/ very little current there anyhow, as the "run" wire goes dead during cranking. One thing you for sure want to do, is check for voltage drop, as that run circuit is very prone, and affects charging voltage. Turn the...

I would say steering gear

Headrests

I'll tell you what might be. That black (how large what gauge?) might be a hacked feed to the "hot" buss in the fuse panel. If so, it originally came from the welded splice as I mentioned. Look on the rear of the fuse panel. There are 3 distinct separate busses. One section is...

Fuses right out of the shop manual. You can download this for free from MyMopar, and the reason that several of those are there is because of some of the guys on here I would pick a symptom and go after it.

There is no ground anywhere attached to a fuse block and NEVER assume that black is ground because it usually "ain't." You keep saying "exterior lights." Does this include headlights? stoplights? Turn signals? Park tail? Some of these come from different circuits and power sources...

DETAILS!! Year, make, model What do you mean, "exterior lighting?" Parking lights, etc? Most? All? of the exterior lighting comes through the light switch, the brake switch, and the turn signal circuit. That wire is either added or hacked. Where does the end in the fuse panel come...

YES

The VR power supply/ sensing wire is spliced to the "run" wire somewhere up there near the ballast resistor. You likely cut it out of the loop when you put the MSD in there. Hard to tell just what you did. A late model alternator (starting in 70) has what is called an isolated...

SHIRLEY it's not a 1943 Supermarine Spitfire!! AND DON'T CALL ME SHIRLEY!!! Or not? a 1928 Farmall hemi powered Regular?

Might?? be for idle stop solenoid. I think they were used on some CA smoggers and also with AC. Here: https://www.forabodiesonly.com/mopar/threads/what-is-this-used-for-on-an-oe-340-intake.570195/

The red is a direct feed, only protected by the poor protection of the fuse link, from the battery. The black carries on through the ammeter and branches off to supply loads, then goes back through the bulkhead to the alternator. You need to at least bolt them together, AND I WOULD...

I think it just depends. If you are adding a bunch of stuff like electric fans, big pumps (and coolant), big stereo, etc, then I would for sure get into it. If it is clean and tight, run it

Just let me take this to again thank all you guys, some I missed, I'm sure. THANK you!! We now have the main floor emptied, but the walls not demolished. It is a problem getting people to show up and actually work. I've had about 4 completely flake out The basement is ?? about...

Just let me take this to again thank all you guys, some I missed, I'm sure. THANK you!! We now have the main floor emptied, but the walls not demolished. It is a problem getting people to show up and actually work. I've had about 4 completely flake out The basement is ?? about...

You still must check and fix the ammeter/ bulkhead connector, as both the black and red are not the conductors for power from the alternator/ battery, into the pass compartment, for power. When I say "fix ammeter" I mean if you hook them together, the red and black, make sure the...

???Thought the Dakotas were screw on clutches

WOW

Well just sayin' but you don't actually have to move it somewhere to get a good ground. Those can be problematic because of the paint/ coating. I don't know whether it's really high quality paint (epoxy?) or powder coat, or what, but they MUST be scraped to metal to get grounded. I am...

Thanks for coming back and letting us know. This is also why manuals are important, and finding out "what all" is on each fuse.