Search results for query: *

  1. Fast340cuda

    Edelbrock LD340 Intake Manifold Usable Max RPM?

    TTI stepped. 1 5/8 to 1 3/4
  2. Fast340cuda

    Edelbrock LD340 Intake Manifold Usable Max RPM?

    The heads have only had a valve job and the bowls cleaned up. I believe the camshaft is a little small, it was ground for a 3.31” stroke but I ended up finding a great deal on a 3.58” stroke crank and some .060” 360 pistons so it is now 371 CID. I feel the car runs pretty good, pump gas, all...
  3. Fast340cuda

    Edelbrock LD340 Intake Manifold Usable Max RPM?

    Edelbrock RPM’s that were touched up by Ray Barton. I use the numbers as a reference. Was more interested in the power curve. I have tried the performer RPM, Weiand action plus, Victor 340 as well as the M1 single plane. I have been the happiest with the LD340 so far on my combo.
  4. Fast340cuda

    Edelbrock LD340 Intake Manifold Usable Max RPM?

    I recently took my car to a local chassis dyno and ran it with the LD340 intake. Combo is 4.06” bore, 3.58” stroke, 11.1-1 compression ratio, solid flat tappet cam (252/257 @ .050, .550 ish lift, 108 LSA). Intake was gasket matched and the plenum divider was cut down 1” and 2.5” length wise...
  5. Fast340cuda

    Another bag and kinda tagged.. Tagged but only as DS and PS

    Those look like the rear/side carpet hold down strips. Should mount under the rear door panels with the front lip tucked under the door sill plates.
  6. Fast340cuda

    Charger Daytona on Mecum

    I was at the auction today and watched this cross the block!
  7. Fast340cuda

    SSI cams

    I checked my PAW catalogs from 2000 and 2003 and unfortunately they only list hydraulic SSI cams for the small block Chrysler.
  8. Fast340cuda

    SSI cams

    I have several PAW catalogs. I’ll dig them out after work and see if I can get you the info.
  9. Fast340cuda

    Factory 383 Pulley Sizes

    Yes, nearly any non AC big block water pump pulley will work for your application. The OD for this pulley is 6 7/8”, the height is 2 13/16”. On the crankshaft pulley, my research shows that small and big blocks shared the same part number. When you are ready to shop check out the small block 2...
  10. Fast340cuda

    Factory 383 Pulley Sizes

    A body is not unique on pulley fitment, they are interchangeable with B and C bodies (even E bodies).
  11. Fast340cuda

    Factory 383 Pulley Sizes

    I used this pulley info from the 440 source website when putting my big block together.
  12. Fast340cuda

    Ralley dash with aftermarket tach question

    I used this Stewart Warner tach in my Demons rallye dash. Fit pretty well and looks similar to the original.
  13. Fast340cuda

    71 Demon 1/10 RC car

    What’s the part number on the body and who manufactures it?
  14. Fast340cuda

    71 Demon 1/10 RC car

    Just finished up this RC replica of my full sized 71 Demon build this weekend. Figured I would share some pics before my son and I wreck it! The body is manufactured by Parma and the car itself is a Traxxas 4WD slash.
  15. Fast340cuda

    A body with an A833 and a Gear Vendor installed

    I prefer the look of the round shift handle and ball in an a body. No cuts at all in the tunnel. Just took a few good sized clearance dents in the driveshaft tunnel. Best mod I have done so far. I run 3.91’s in the rear and with the OD on it cuts them down to about a 3.0. Makes cruising on...
  16. Fast340cuda

    A body with an A833 and a Gear Vendor installed

    I’m running a Gear Vendors unit behind an E body 4 speed in my 68 barracuda. My kit came with a shifter mechanism relocation plate to move the shifter mount from the E body to the original A body location. I ran the B body bench seat pistol grip on this set up initially but am now running the...
  17. Fast340cuda

    can a 440 be installed from underneath?

    I just installed my 440 from the bottom in my 71 demon with the k frame, transmission and headers attached this weekend. I had no problems at all during installation.
  18. Fast340cuda

    [WANTED] 67-69 small block 394 oil pan

    Looking for a clean 394 stamping oil pan to install on my 68 340. Ditched my stock pan when I was in high school for a deep sump Milodon. Ready to go back to stock and gain some ground clearance. Let me know if you have a nice spare sitting around! Thanks FABO!
  19. Fast340cuda

    [Found!] 1972 dart or demon twin hood scoop

    Looking for a twin hood scoop for my demon project. Prefer one off of a 1972 dart or demon but open to the dart sport version for the raised center section hoods. I have been looking at the reproductions but would really like to find an original. Car is just about ready for paint and this is...
  20. Fast340cuda

    Favorite Big Block Roller Rockers

    They had a few sets on the shelf when I called last year. I believe the company was previously named Rocker Arm Specialties.
  21. Fast340cuda

    Favorite Big Block Roller Rockers

    I just installed a set of Rocker Arm Unlimited rockers on my big block. Have not run the motor yet but they seem pretty solid.
  22. Fast340cuda

    Clearcoat on engine

    I have used spray can clear on intakes in the past and it did turn yellow after some run time. It also stained easily when gas gets dripped on it. This last round I used my spray gun to shoot base and clear but have not run it yet to see if there are any issues. The local shop that I purchase my...
  23. Fast340cuda

    Plastic model kit

    Received my reissue kit a few weeks ago. Really nice kit overall, details are fairly close to the original I have.
  24. Fast340cuda

    Anybody use the 440Source A/C body oil pan?

    It took a fair amount of solid swings with a good sized hammer. Glad I mocked it up before assembly and paint!
  25. Fast340cuda

    Anybody use the 440Source A/C body oil pan?

    I have the Mancini pan on mine which I believe is the same as the 440 source pan. I had to slightly clearance the oil pan for the idler arm to clear when the steering was at full lock. This is with a DC k frame and the original steering linkage from my 71 Demon. The attached pic is prior to the...
  26. Fast340cuda

    Engine compartment pics

    372 CID (340 based) in my 68 340-S barracuda
  27. Fast340cuda

    Hemi oil pan

    Here is a picture of my set up. Im using a 66-69 hemi oil pan on a 440 with the DC spool type k frame. The bottom of the pan sump is about a 1/2” lower than the bottom of the k frame so I added a reproduction skid plate for safe measure.
  28. Fast340cuda

    BB Oil Pump Difference?

    Here is a HV Melling for reference
Back
Top