Search results for query: *

The engineers of that engine put a canister filter on it by design. I don't understand how you think you can improve on it for one thing. Secondly, I've never seen a filter with any sort of anti drain back valve that was 100% leak proof, especially when the filter installs upside down. Like on a...

I have installed both Hellwig and Hotchkis rear sway bars. The install is a little different, the Hotchkis requires welding on the hangers while the Hellwig can be a "bolt on" operation. The Hotchkis install is probably a bit cleaner though. Addco has very cheap hardware.

I'm Still working on this Ford Timing Job...... :mob: May be done tomorrow.......

It's about 7 years old

#20 #45 Bristol kids night

What's up Hot Rod?

So the tester I have is the old school resistant type tester (where you hold a switch on the bottom for 10 seconds and watch the gauge to see where it falls). I also used a larger group size battery for testing from my 04 Ram SRT10 and saw no difference. I don't have an ammeter, I have a volt...

I don't have a dial style torque wrench so not sure I would do a drag test to be honest...

Ok, thanks I will try this, what I did was disconnect the positive battery cable, on the Jeep all you need to do is under a 10mm nut and yhe cable, not the terminal pops right off, I'm not sure how that is different from disconnecting the negative sensor but I'll give it a try this morning...

You can build hp with various ratios of basically duration to head flow, look at LS engines they build 450 hp with 218° cams, say OP hits his goal with his 230° cam as long he has decent gears and stall to go along with it shouldn't be fine.

You will find that with the softer hit of the 'tamer, shock settings won't need to be as tight. Grant

These are the ones I have. No bends, kinks, ding, nicks etc. Not mint but very nice & will look great with a good polishing. Again, I took them off a 74 Duster I had but should be the same as yours.

Thanks. I’m in Canada, so a $3.00 gasket will cost $20 shipping. I was asking if anyone else got an oversized one to see if mine was a fluke, or are they wide-spread incorrect.

All the other lights work except trunk, dome, map. Thanks for your help . I'll keep searching.

Transmission and shifter have been SOLD.

Little nuances like this are a fun part of the hobby .

Yes .. but not so much that most notice . Pedastals are shorter and angled different at the base if memory serves.

The car was ~3200 lbs w/ driver, tracks around 1000' elevation.

If you're hearing rattling down low it's more likely rod bearings than mains, so if you're in there change both. It can be done in car and it's fun!.....well, minus the fun part. Regardless, 20W-50 should improve the issues without turning a wrench :)

Morning

This is the "light duty" spring.

My son is outside Grass Valley. They were not allowed to put in a paved driveway (probably around 150'). The gravel was just laid on the dirt. It is unlikely the little single lane bridge over the creek to get to their place will support 70k lbs. Weird rules all over...Also, it would be very...

I have one new 1.6 ratio Crane roller rocker arm in its original package. $30 plus shipping.

Welcome from the Garden State!

Mr. Norm's Tri Power air filters. 100% correct. Very limited quantity available. Less than 20. After not being able to find one for my car, I found an air filter company that was willing to make a small run of them, using my original dirty one as a template. Price is 299.00 + 20.00 shipping...

To the op.. I have always bought a second hood or part to do modifications to so if all goes wrong.... In this case I'd buy a fiberglass hood to pin on and put scoop on and tall air cleaner... Attach the 4 pins with bolts (don't weld on..). Paint both hoods and you have the best of both...

Top row are aided with clips and bottom row screw directly to dash. All are recessed so head is flush with dash. Top row are also grounds. Do you have the correct screws? they are special.