Search results for query: *

when i installed super shifter in my duster, i made a plate to raise the shifter up. i used 1/2 inch aluminum plate, i raised it up bout three inches, trimmed hole in floor to get it in. just food for thought

wether you're a fan or not, truth is, pot holder magnets work period!!!! springs and dampners are the biggest trash makers in an engine. put them in and see . i'm not b## sh##ting any one, they flat work,

looks like you have dual springs with dampners, on drain back areas , install pot holder magnets to capture metal seven per side .

i know that valve springs and dampners wear metal, into engine, i installed pot holder magnets in drainback hole in heads, takes 7 in each head, i no longer have metal in the pan, it cured the problem. when i pull covers off, they are covered with metal, pull and clean them. simple fix. just...

i have a dana 60 in my duster, didn't have to modify the tank. it fits, if you use one of those thick back covers, yes, a steel cover fits easily.

mcloed makes a 10", disc, its a sintered iron disc, number is 5007-02 for 23 spline, or 5007-05 for 18 spline, they are aggressive, bout like a puck disc. also solid hubs, just food for thought,

my 273 used felpro 1243, it fits 273 /318 ports

reason is sst rod will weld to cast and steel, rods like 6011 will not weld to cast. just food for thought

find a dana 60 from a 67 to 72 ford 1/2 ton pickup, its the lightest, diff in wgt is 35 lbs, it has passenger car ends , weld case to tubes with stainless rod, mine has been in my car since 1992, it has bout 3000 runs on it. just food for thought

i've never torqued them, i did tighten them up tight, with 3/8 drive ratchet . just food for thought

on my 66 dart, i run just the resonator, sounds wonderful, had one guy say, never knew single exh could sound so good.

our gk stocker cam is at .006 cold, makes it .004 hot, seems to work ok, no problems, had a comp stkr cam called for .006 lash on intakes, zero lash on exh, int was a solid lobe exh was hyd lobe. just food for thought

not all 8 3/4 cases are same. i measured the case and the cap differences, using factory gears , already shows how much shim to use, after market gears have to use pinion depth . with a t & d gear setter, it measures absolute pinion depth .for years i used flat plate and measured depth, with a...

which rear end are you working on? 8 3/4 bores are not centered, dana's are centered

you can weld the rack with cast welding rod, muggy rod is the best one to use, its made in wash state. they have a web site. far better than brazing.

the clevite 318 mains fit, number is ms 1344P, all bearings are full grooved

mopar race manuals, says have to pump 1 gal.in 25 seconds or less. that is Minium volume. i use a areomitive fuel pump and reg.and 1/2 line. just food for thought

also, gear ratios are different. a body is 3.09, .1.93, 1.40, b body is 2.66, 1.92, 1.34

i have the mini starter, its a tight fit . looks like have to remove starter to get manifold in, then install starter

does steering column and starter have to be removed to install manifold? been long time since worked on this. thanks

question , about exhaust manifold on 273 dart. does steering column have to be removed to get left manifold installed??or the starter? its been a long time since i worked on one of these, thanks

when you change ratios, you change everything, 1 st ,2nd , 3rd gears, cluster, input shaft, you don't change reverse gear. some gears show same tooth count, but are different dia, won't fit. you can't mix and match gears, all are specific to each ratio set.

the 64 to 66 six cylinder trans has the 3.09 gear set. , it drops in, don't need to change reverse gear either, i had a friend , changed to a 3.09, from a 2.47 gear set, in 1/4 mile it was two tenths quicker, the 340 will pull the split on 1 -2 shift easy. i ran the same in my 340 car, go for...

i read my post, it was 10.05 @ 131.7 mph, he dialed a 10.11 broke out, it was at brainard earlier this year. index is 11.00. he can run with the 283 chevs

it was at brainard at the div race as i remember, i didn't save it, just seen a vid taken at tristate he ran 10.5 @ 130.12 it's called wheels up slow motion, by jerry nesh

he runs ss/k stick shift, i seen the video of the pass,

its matt stein, its a 66 valient, 235/273, runs ss/k, seen where he ran 11.05 @ 131.76 mph. very impressive combo

I attended a seminar put on by superflow,in 1999, harold betts was the speaker. bottom line he stated was, port shape and port velocity is everything, don't get hung up on flow numbers. port velocity fills cylinders' fast and creates more cylinder pressure, which makes more torque , also power...

i made a alignment shaft for my 18 spline, clutch. i measured od of shaft and made it out of aluminum shaft, it fits in splines very good,, no splines to mess with, way easier to use, btw way that plastic alignment tool is worthless, thats why i made my own no splines. the end was turned down...

on our stockers , we run zero lash with hyd lifters, also run anti pump up style, our engines will run to 7500 rpm, cam is 262 .265 duration at .050. lobes are very aggressive . just food for thought, btw , springs are 140 seat and 360 open