Search results for query: *

That's because they ARE two different things. The question is, which one does YOUR car have? 1967 from the factory has the first — the narrow lockstrip. Is that what your windshield gasket looks like? For future reference, if you are asking questions on this forum, tell us the year, make and...

Days

Agreed. Just did mine on my 8.8 and it was a PITA. What method did you use to connect to the factory cables? I had to fab some mounts to use the soft lines and even then they had to bend pretty sharp to point in the right direction. Only other option was to put them between the Ubolts. Sucks...

The book is Horsepower Chain. 45 deg seats have more curtain area at low lift than 50 degree seats and should always outflow the 50s at 0.050", 0.100" and usually 0.150". A tighter throat 'may' choke off 0.050" flow a little but it will help 0.100" and 0.150" flow because it helps the high...

No, ones a right and ones a left, or at least they were on both sides the engine when I took them off.

It's pretty simple, do you have windshield moulding clips for a '68 up style stainless trim or just the rubber gasket that I show VERY clearly in the link provided in post #4.

I don't have flow numbers or air speed. But with a Crower 31409 cam and 11.2 compression you can make 680 hp with the Bloomer heads.

i never got this "actual miles" thing whatever else miles would they be, canadain miles? sea miles? cyrus miles?

hi Tooljunkie, you're always busy ...love it

I believe the spring perches on stock A-body housings position the pinion pointing 5* upward.

I see 2 different things but is hard to tell by looking at the pictures. One is a thin trim that locks into the molding but doesn't cover it completely. The second one i see covers the entire molding and fits flush into the body

On the dyno, my 440" W5 street engine made 644hp and 585 ft torque with the M1. 655 hp and 602 ft torque with the indy. Both un ported just gasket matched.

I’ve hearing some people made these over the years I like to get in contact if anybody has a good use one or a new one or a machine shop.. that I can contract and make one through Thank you Kevin Haranczak

Goodafternoon! Went out to my truck to find it covered in ice. So are the highways. Last panel in and done, welded,ground and im starting with the fiberglass filler. Almost at an end.

That movie was based on a small town not far from here. Damned if i can recall the name at the moment.

I know there’s epoxy in the bowls so you do have to deal with that. You are making my point. The curtain area is smaller with a 50 degree seat. So you are shrinking the bowls (or a better way to say it is keeping the bowls smaller as a percentage of the valve size) so when I see gains in low...

1967 only windshield gasket "lock strip". Did the Wife's Barracuda Formula S in the past week... https://www.forabodiesonly.com/mopar/threads/what-did-you-do-to-your-a-body-today.572423/post-1974896095

I believe there is an angle built in to the perches on the housing. I get the following. With the center section of the housing plumb, the perches are 5 deg I took photos with the housing upside down So with the housing perches level the center section mounting surface would be leaning...

I'll bet he did

Post some links to the parts you are talking about and a photo of the part you plan to replace

Or wrap it

I tried both the dual carb tunnel ram set up and the single carb/Indy port matched intake this past season and there was very little difference in ET/MPH between the two. I've had the M1 W5 intake sitting around for over a year now so I'm going to give it a try. If I don't like it I'll put the...

Single blade cutters. The throat is now epoxy which does not hold an edge as well as the steel would. Just curious. Why do you pick out the 50 deg seats as being bad at low lift. The 45 deg seats should be better than the 50 at low lift. And a smaller throat will help low lift flow on a 50...

https://www.classicindustries.com/product/mp14061.html Note they do not make the barracuda version but as I understand it the Dart version will fit but the trained eye will notice the difference.

The 50. Look at your low lift numbers. Are you using a cutter or stones to do the seats? Edit: I forgot to mention your high lift numbers. Or mid to high lift anyway. I care far far more about the shape of the curve over .25 l/d than I do low lift flow numbers. For me, testing low lift (lets...

I think he changed his name but not sure to what. Kim

make sure this is correct...Bell housing 289 2482 = 10.5

The consensus seems to be SEMS Hot Rod Black or John Deere flat black. Do a search for "black hood paint" in the body forum, there's lots of threads on this.

I only have the smaller ones left in my stash. I dont see a 67 anywhere at the moment.