Search results for query: 318 cams

That’s a cam to increase mileage for sure! I think you are confusing two aspects of this and it starts with what YR is saying and how others are just simply wondering about a low dyno pull rpm test in addition to cam size, and I note see engine usage. YR is correct in his words but the...

seriously if going stroker buy the kit!! lot cheaper and easier than piecing it together your self and itll come already balanced!!! but if your going stroker youll need better heads than 318s, alot better!!! lotta folks hate on the big muther thumper cams cause a cam spect to yur build will run...

True overlap likes long tube headers , but most wanting to run manifolds are probably not trying to push it over 350hp with fairly mild cams doubt even with something like an xe268h cam the difference between manifolds wouldn't grow much if at all, what I take away from it any 360 manifold is...

Id choose the 110 for a 318. 108 for a 360. Dan, can you post links to each of the cams your thinking of? Thanks.

That's what I'm talking about pulls like a freight train

Are you talking the regular red or the gold? The gold series have both sprockets nitrided. I've never had any issues with the Rollmaster sets and get pretty good mileage out of them. I pulled my 265 down last year for rings and bearings and decided to throw a new chain on while it was apart...

I've had some experience with a 360 industrial / truck engine once that had an oddball casting number of 857. They where like 234 industrial heads except they had exhaust instead of water going through the manifold crossover. They where small port like 234 industrial, so I imagine they had small...

30 or 40 months s not a kid. LMAO! Gas sucking by today’s standards! Fo-Sure! I did get 20 Hwy w/2.76 gears on 235/50/15’s in my ‘79 Magnum. No headers, just a decent tune and dual exhaust/a Carter 600, MP distributor and 2-1/4 dual exhaust with some turbo mufflers, as the non stick items...

does that cam not fit a 318 LA? it says it does, 273-318-340-360.

Title question pretty much spells it out. If I can't find any "made at least 25 years ago" and have to buy more current stock, who's good, or at least "less bad"? I have a set here that (I don't know why anyone would keep old used ones around) I bought from a swap meet, I know the guy who sold...

The worst case of s you take the entire engine apart and clean it up, put it back together and install the new cam and go. That route sucks if you have a failure. “IF.” The other thing with the cam as 273 was pointing out is the duration (actually what is really important, the overlap) dictates...

Get real. You want to compare, then compare apples with apples. The 302 Ford was their economy engine. So compare it with a Mopar 318 or GM 305. In emissions guise these all had crappy cams and lower compression. You want to compare your 340, do so with the competition performance engines. The...

In 69 the 273 had hydraulic cams and stamped steel rockers along with the same cam as a 318 2 bbl...

I ran the torker 340 on 2 nitrous motors 1 318 340 heads the 2nd a 340 318 had the hemi grind 340 had a g/k 243@50 108 both setups had 3.23s the 340 setup started as a 4sp put a 727 in it then back to the pistol grip 4spd dp on both setups the nitrous made up for the longer cams and not enough...

The rockers you have are superior to the hydraulic style. Stay with them and get push rods . You will be able to adjust your hydraulic lifter preload with the adjusters rather then using shims under the shafts. And most of these new lifters need adjustment and do not work with the stamped steel...

While I agree with you, for someone wanting to switch from solid to hydraulic the hydraulic system is so simple and they work just fine.

If you want low end torque, then a 318 is probably not for you. Even if it's built to maximize the low end , it's not going to have much . It's simply too small. But then my daily drivers for most of my life have been big blocks. Anyways... I think we have gotten a little off course with this...

I've mentioned several times that I'd love to see the same kind of analysis I've seen with big block cam selection or even stroker/340/360 cam selection applied to a reasonably mild build 318, with no other mods but, say a 4 barrel and dual exhaust, and maybe starting with one of the 9.2:1...

I couldn't give you time slips if I wanted to, as there isn't any tracks around here and dyno pulls, I don't have the funds to pay for something like that

1972 Dodge Demon originally B1 blue 318, now B5 blue with 408 stroker, power steering and 4 wheel disc brakes (BBP), original interior, except radio, gauges, and kick panels(included). All lights, gauges, heater, wipers work, the horn does not, fuel gauge reads E at half tank. Leaks 1-2 drops of...

Almost all poly 318's and '60-7? slants have solid cams from the factory too.

The reason I like 273's are they have small port, closed chamber heads, that will flow almost as much as 360 heads. From 64 to 67 they had solid lifter valve train and cams, forged steel cranks, and bushed forged steel rods. Pistons are almost to the deck and nut sunk like the larger motors...

Ok, been looking for a 318/5.2L .432 roller cam to put into a 5.9 ever since I read about them to get a little extra something out of an otherwise stock setup. As I understood it, these were PRE magnum cams. So, I pulled one from a 85 5th ave and it measures 0.390 (.260 x 1.5).... ?? Are the...

I used the roller version of that in a 360 mag with 11.1 compression measured. It was an absolute torque monster in a 78 power wagon, pulling an open car trailer, the first time my cousin rode with me, I opened it up. He said holy ****, this thing revs like a dirt stock car. Idle until the...

There's tons of 318 cam threads here. There's info on a few cams that are specifically ground for a 318 with a 4 barrel and dual exhaust. I just looked through my bookmarks and couldn't find the thread. Sorry.

That's Melling. Not Chrysler. Specs could very well be different and they usually were in the aftermarket.

The alloy heads when combined with a tight quench, will support very high cylinder pressure on pumpgas . Good luck getting there with flat-tops and a 340 cam. It will never happen. See Note-1 If you ignore the pressure possibility, the guy in the next lane with an identical set up but pushing...

Thats a decent cam. But for stock long block 318 I would chose a cam with a faster ramp. The difference between the duration @50 and the advertised duration. The larger that number the lower the cylinder pressure will be. With a stock 318 your compression is already low. Any of the new cams like...

This may not help the OP, but the SUM-6900 cam and lifters is what I ended up using in my 74 318. Bone-stock low-compression bottom end with the cam, duals, and an 1406 Edelbrock on a Performer intake. I currently still have 2.76 gears and a stock convertor. I noticed no loss of low-end and...

In my book, the windage trays, distributors, and camshafts are not the "same". Will they bolt on? Sure, but, they're not identical. The windage tray needs to be tweaked a bit to keep it from rubbing the crank if you put a 318/340 tray on a 360. Cams and distributor specs are different.