Search results for query: *

there are good double flare tools like the one from eastwood and a little cheaper - shop around - I buy tubing from autozone and make my own lines - what works is patience and also using a piece of hard wire to make a mockup of what you are trying to do - also get a bender for 3/16" tubing -...

If I can get the blue mutt roadworthy enough, I would be up for the ride

slow and tedious progress, electrical clean up time, took a closer look at the bulkhead connector - down the rabbit hole I went - have upgraded the electrical and now mostly done the carnage if you don't think that the factory splice in the dash is worth at least looking at - heres a good...

Sent you a PM, I'm local

test of patience - ready to go for a ride

As I mentioned I have been working on doors, etc., I have things to do under the car but working on finishing everything up top before it hits the jack stands again, after some cleaning, slight adjustments I got the rear seat in along with the rear panels. My passenger door needed adjusting and...

Currently I am working on the doors and finishing the trunk - my driver's door was a 68 so I'm converting to a 69 with proper hardware, the previous owner had a fuel cell in the car and had cut out a section in the tire well but filled it in before I bought it, I did a little clean up inside as...

The car had what appeared as it was somewhat newer but the guy I got the car from has installed numerous things and it had a lot of holes - so new carpet time, I did use a piece of the old and extended the carpet all the way under the rear seat - more quietness but probably not much, also new...

Previous own installed a very cheap stereo and cut the dash slightly - a factory radio can still be installed and the trim plate will hide the cut if I ever want to return to a stock one but I am upgrading with a nice stereo and speakers - part of this required some rework to the rear speaker...

column laid out for final assembly and back in the car

My car was an original column shift, it had a B&M shifter in it when I got it so I got a non-shift column piece and commenced to completely rebuilding and cleaning p the steering column, that's when I found out the mutt has another mix of parts, my column is from a 67 - woohoo, anyway got...

had some more slow progress - derailed by a few other projects and life - catching up a bit. I realized that as I have worked on my cars over the years I always seemed to leave something that I would finish later, I am trying to completely finish this time with everything which leads to testing...

I bough my dash speaker hear, I think it sounds incredible Home | S&M Electro-Tech

Thanks all, got one on the way

@ dutchrebuild - I am not sure - @ mbaird - thanks for checking

mbaird, the top one in your pict matches mine - it is the passenger side though and I need drivers side, do you have one of those?

Hi all, internet has been out - so confirmed 69 is one year only, received a couple of chats and responding to now - standby may have located one.

Heres a few - will be great if you have one Thanks

I need a driver side door latch for my 69 Dart, I had bought one a while back and just ready to install and it is no good - I can get picts of what I need if it will help, Thanks,

good and bad news @ hemi - that was my plan - my problem was getting my previous working 69 reassembled correctly So the picts from CFD244 help me figure out my issue - big thanks - I was putting the rod in the wrong spot causing bind and it just wouldn't work - pulled the plastic retainer out...

Hemissdart - the other (driver) door is a 68 - doesn't have the lock rod which I am converting 4spdragtop - that thread helps - Thanks CFD244 - from the looks of things I put the clip in the wrong hole on the latch - will check and see - hopefully its that simple @ All - Thanks - good thing I...

Throwing in the towel - having trouble with the door lock rod on the blue mutt - 69 Dart passenger door - other than a little adjustment and everything sort of worn my passneger door locked/unlocked fine - but I decided to take everything out and replace the plastic clips, door handles, lock...

the champion fan/shroud would likely work if your looking for electric

worth every penny, browse through similar to get best price

bump

a FEW MORE PHOTOS

Holley 750 Near New 0-4779SAE Decided I will be going a different direction for carb setup. I bought this carb a couple of years ago, when I put it on my car I assumed that the linkage was the same as my 670 I had on it briefly but it was different which kept me from getting the carb to idle...

progress - been sloooow to happen with the work on the yard as well as some other misc chores, gas tank is in the car, rear is back in the car, will soon put the new new brake distribution block in, finish the break connection and the back end of the car will be done, installed new supply and...

I keep reading a few posts from this thread but haven't read it all, lifes journeys are great sometmes even with the sideways trips we endure. I still haven't figured out for sure if your back in western wa but if so, once the blue mutt is ready to get out of the garage again maybe we can catch...

make sense - I hope to have my Dart back together soon, hopefully the 360 performs well enough, if it doesn't I had convinced myself it would be blueprint time. I will keep an eye out, your up the road a bit from me but more local than most others here I would say. Good luck with the sale.