Search results for query: *

I've used them on my circle track mini-stock and they seal fine.

I run an ATI Superdamper on my 340 Sport and on my mini-stock racer. I don't use anything else.

I've run a Comp Cams solid flat tappet in my built 73 Sport for 5 years with no issues. As others have said, proper and timely break-in is critical. No shortcuts. And proper oil from then on. I'm running Amsoil with ZDDP and absolutely no problems.

Since I grew up in the 60's, if it was mine I'd go with an original 383. Only because I saw so many in my youth and always loved the look of the Darts, plus that 383 emblem on the fender. I know, a silly reason.

I level the car with the jacks under the rear axle tubes and on the frame rails up front. I measure the ATI damper for the front reading. Whatever that is, I try to get equal but opposite at the rear, measuring off the rear end yoke. Has always worked on my street Dart 340 Sport and my circle...

I have the Summit 2.5 inch with H pipe setup and the Dynomax Super Turbos on my built 340 Sport. I love the sound from the outside. Inside, not so much. Cannot cruise and listen to the radio/CD player due to the noise.

Lots of opinions here. I run Amsoil Dominator 10W-50 in my mini-stock flat tappet engine. No issues at all. For my built 340 Dart Sport with a solid cam street car I run the Amsoil 10W-40 Z-Rod with the zinc.

My build is similar to yours - 73 Sport 340, Eagle crank with H-beam rods, JE flat top pistons, decked, Edelbrock heads, RPM Air Gap intake, 750 Holley, Schumacher headers, 3.91 Sure Grip and Chevy 200-4R trans. 1.6 roller rockers. I got with B3 Engines for their geometry correction kit for the...

I think of the Restorations page as a place to show what you are working on, not what you've already completed, along with notes on what and how you're doing it. This page is where I learned the basics of adapting a 200-4R trans to my Dart 340 Sport. And that's just a small part of what I've...

Bolts should stick out at least by the diameter of the bolt plus 1/8.

However you end up lowering it, be sure to check your pinion angle afterwards.

73 Sport. Built 340, Chevy 200-4R Trans, 3000 stall, 3.91 Sure Grip. Ran mine through the radiator and then the cooler, then back to trans. No issues. I also have the finned aluminum deep trans pan.

This is the Wilcap adapter behind my 340. What's crude about it?

Actually its 700-R4 and 200-4R.

The Wilcap adapter is not an ugly piece at all. The poster must be thinking about another one. Here are two photos of my adapter. The kit comes with everything you need to bolt a 200-4R to the 340. And there is nothing at all to cut from the engine block or the trans. I am totally satisfied.

Try Mymopar.com and download a service manual. You'll find a wiring diagram there and you can follow the path from the sender to the gauge. If it's like my 73 Sport 340, there's a connector behind the driver's foot panel where you can find the wire color specified in the manual. Locate that wire...

Check out Wilcap adapters. I used one of their adapters to put a 200-4R behind my 340 in my 73 Sport. Fits without cutting the tunnel at all.

On my non-Mopar race truck, I use the ATI Super Damper for my engine/trans angle. Then to the rear with the equal but opposite deal. Has always worked for me.

I've found that Honda Bond works well when RTV seems to not seal as I'd like it to.

Would love to know how all of these different brands compare with the stock-sounding mufflers offered by some companies, such as Accurate. As an old guy, I still remember how nice the 340's sounded from the factory back in the day. As an aside, I have Dynomax Super Turbos on my built Sport 340...

Check out Schneider Cams offerings. Used it in my mini-stock race engines for years runninig a solid cam.

I got the brass.

Got the one for my 73 Sport from Rock Auto. Last year and no issues.

A little something to keep you energized and working to your goal. My 1973 Sport 340 before and after my 4 year restoration. Mine was similar to yours - rusted out floor, both quarters and tail panel rusted, one fender replaced, new interior, new suspension. All the work you do will be worth it.

ATI Superdamper on my 73 Sport 340 and my Ford mini stock race engine. The benefit really shows on the mini stock when I do a tear down at the end of the season.

I know every car is different. I have a 73 Sport with a built 340. I used the Dynamax Super Turbos to replace the Summit Turbos I originally had. The Dynomax sound good at idle, not too loud, and really sing under throttle. But the interior drone is terrible.

I have Dynomax Super Turbos on my built 73 Sport 340. Sound at idle is nice and it sings on throttle, but the interior drone is terrible.

Just for thought - print the wiring schematics and then get a long piece of cardboard and tape the schematics to it, in order. Makes following the flow of the wires much easier. You can fold it up when not in use. Believe me, you'll use it a lot.

May be relative after you install it - I have a Detroit Locker in my 427 Cobra replica. I've noticed that if the air pressure in the rear tires is unequal side to side by as little as 3 pounds the rear will have a slight jerk to the right with every shift (Toploader 4 speed). Also, get ready for...