Search results for query: *

Last fall I noticed some water in the taillight of my 67 Dart. I pulled it apart and found where the water leaked past the gasket. I put a new gasket set in the taillights a few years ago. What is best to secure the gaskets to the housing? The tabs in the lens(where it screws to the...

Just out of curiosity, I wondered if there were rare multi carb intakes for Chrysler engines, primarily small blocks. I have seen the 2 four barrels and 3 two barrels, but wondered bout the multiple (6-10) single barrel intakes or any other off or rare intakes.

How do I remove the back from bucket seats in a 67 Dart? Thanks Aaron

Ran over a deer with my dart this morning, it was already dead laying in the road. Doing around 70mph. Didn't see any body damage on dart, some flesh and blood on frame rail. What should I check underneath? Seemed to drive fine, but plan on having alignment checked. Thanks Aaron

One of the taillights on my 67 Dart has about 1 inch of water in it. How do I fix this and prevent it from happening again. Thanks Aaron

Don't hate. I was asked to change power steering pump on girlfriends folks 66 Mustang, 289 v8. From my online research the car has an Eaton pump, their son in law ordered a replacement and the replacement is a Ford/Thompson pump. I don't know what will interchange on Ford's. From what I...

Been looking at cordless impacts to carry in car for emergency tire changes. I can't justify paying the prices they want for DeWalt or Milwaukee. Porter Cable seems to be the cheapest I have found. Any opinions or suggestions?

I have hauled dignitaries in a few parades, I don't like people sitting on back of seat, so I threw together a bench to replace the back seat for parades. Going to try it out tomorrow.

I am trying to figure out a temporary passenger side mirror for my 67 Dart. I would like to tow my teardrop camper a few times. I have a 70s style temporary fender mount tow mirror, but the arms hit the ridge of the fender. I have thought of rigging a backup camera but am not sure if how long...

Took the front 10 inch drum brakes, backing plates, shoes, drums, hoses, ( minus the hubs) to a swap meet, guy was wondering if they would fit a 66 a-body, they are off of a 67 Dart. Told him that my understanding was that it would bolt on 10 drum spindles, but not 9 inch drum spindles. Told...

Just sent my switch in for a second rebuild(5 years since first rebuild).this is his response "What I want you to see it the amount of arcing occurring. This switch is really getting hot while in operation. I would inspect the wiring terminals on the switch and motor side. I believe there is...

I am doing a few mods on my 67 Dart. I want to do sort of campy mods that might have been done back in the day, but want to keep it easily reversible back to stock. Thinking of doing a sifter knob/handle on the stock floor shifter, possibly utilizing a beer tap handle. Anybody done a custom...

Putting an aftermarket steering wheel in my 67 Dart. An old school chrome wheel with the plain round horn button. I would like to add an emblem to the horn button, either a fratzog (Dodge Delta) or "GT". I am thinking something around 1 1/2 to 2 inch's in diameter. Any ideas? Thanks Aaron

I replaced my power steering box with a steer and gear box, now the steering wheel is off by about 45 degrees. How do I rectify this. No other parts were replaced. Thanks Aaron

Either the screw or the piece it screws into is stripped on the upper pivot of one of my vent (wing) windows. Is there an easy fix? I have thought about replacing the pivot and screw. How does the pivot come off? Does it just slide off of the little post? This is on a 1967 Dart, but the...

This tire was the spare for my Dart when I bought it in 1993. Just wondering how old it is, it is a Toyo "E-31" bias ply, size 155-13/6.15-13. the code in the oval is W53379. No I don't plan on running it, just curious. What does one do with such a tire that has never seen a mile? It is too...

The zipper on my back window has come apart,looks like it skipped a couple teeth and won't stayed zipped together. I currently use the hang strips with snaps to keep the window up, but with the side windows down it flaps and make an annoying noise. I know it needs a new top, but its not in the...

First I will explain what I want to do, so maybe it will make more sense. I want to run a set of cal custom valve covers on my 273, but I don't want to pop the knockouts out of the valve covers instead I want to use the twist on oil fill openings for the oil fill and pcv, using the 273 pcv cap...

I am looking for the bulb receptacles for the dash turn signal indicators for a 67 Dart. I have the fender mount indicators and have hard time seeing them in bright sunlight. Thanks Aaron

Last summer I put new O-rings in the power steering control valve to fix my power steering leak. Good news is it fixed the leak. Got the valve almost adjusted right, jerks just slightly to the left on startup, but it turns hard one way and easy the other way. Any ideas? Have thought of...

The Car Craft project car Dart Swinger will be on an auction this summer. Sullivan AuctioneersUpcoming Events » » HUGE COLLECTOR CAR & ANTIQUE TRACTOR COLLECTION

Rebuilt the power steering control valve, new power steering pressure hose, and now my steering is stiffer than it was before. Before it was the typical light, oversteering chrysler steering. This is on a 67 Dart GT with 273 2 barrel automatic. I would prefer the light steering. What do I...

Would like to put down some sound deadener and cover it with trunk mat material over the rear end hump in my 67 Dart convertible. Thinking of using the sliver stuff from home depot/menards then putting trunk mat over it. Is there someplace I can buy bulk trunk mat material that would match...

Found I have a pin hole in my power steering pressure hose, Where can I find a new one. O'Reillys and Rock Auto show one, but the picture looks different, if it will work that is no problem, but at $188 and $136 I want to be sure. Are there any alternatives? Thanks Aaron

Why are mopar parts so scarce at swap meets? Went to probably one of the biggest non-marquee specific swap meets in the area, drawing sellers and buyers from at least 4 states. And only a handful of mopar parts.

I have an 8 track player (sorry not for sale)that I would like to get restored, and have been doing some research and have read that new in box is not always a good deal as the factory lubricant has likely gelled up and that the belt is more than likely shot.

Looking under my Dart the other day I noticed that the rebound bumpers on the lower control arms are only about a 1/4 from the frame. Would this cause a harsh ride on rough roads? I would like to raise it up some, will I need it realigned afterwards? Thanks Aaron

What does the date on the certicard indicate? Is it the date the buyer took delvery of the car? Thanks Aaron

I accidentally let my collector insurance lapse this winter, now I am trying to get new collector insurance and am wondering what value I should put on it. It is a 67 Dart GT convertible, rebuilt 273 2 barrel, automatic, bucket seat with console, no rust through, some paint flaws, scratchs on...

Thinking of putting a 4 barrel on my 67 273, 2 barrel Going to a swap meet next weekend and wondering if anybody can give me the numbers to look for on a cast iron manifold, will also be looking for a edelbrock ld4b. Not very hopeful about finding something, but you never know, besides it...