Search results for query: *

Looking for someone to media blast and spray gray primer on my 1966 Barracuda. The car is on rolling frame stand (not a auto twirler). What is a reasonable price to expect and If anyone has any recommended shops let me know please. Also any good advice for this project is welcome...

Ok this is what I have done so far. 1. Remove Upper control arm bump stops 2. Jack up car, remove wheels The bolts will not move, i have used oil and let it sut for over a day. I have used a 24" pull bar I have used a 24" pull bar with a 36" black iron pipe for more leverage. I...

Need advice please, I have a bolt that is striped out and will not tighten up where the bumper support bolts to the frame. Should i try Helicoil, Time-Sert, or drill all the way through and bolt and nut it?? Thanks for your time..

Looking for a 4 Speed hump for a 66 Cuda... Also need measurements to install...

Hello, Getting going on my 66 cuda project and though I would ask you guys 2 questions or opinions really. 1- 4 Speed hump??? The Car came with a 904 and I would like to convert it to a 4 speed floor shift one day, but for now so I can get it up and enjoy her I will be putting the 904 back...

Any way to open trunk without key.... ---William

I would like to buy the Auto Twirler Mopar Body Cart for my 66 cuda and just wanted to know if anyone has used one and make sure they work as advertised. Also if some one makes anything close to this i would like to look at them as well. Thanks for your time... ----William

Would like someone to give me a good review of a car for sale in the Hot Springs National Park, Arkansas area...

Still looking for a 1966 Cuda driver side rear quarter panel.. William

Still looking for a 66 Cuda Driver Side Rear 1/4 Will

Looking for a nice driver side rear quarter panel for a 66 Cuda Will

Looking for a solid body 66 cuda... let me know what you have and price please... It can be with or without Motor, Interior, Trim etc.... I'm not a body man so i need a good starting point. I have a 66 that the Driver side rear quarter has been wrecked so i have 99% of the parts i need...

Need some info please. I'm looking at a 66 cuda that someone has put 65 front end on. I would like to put it back to a 66 front end. My question is does the 65/66 front frame the same? Can i just swap the sheet metal? The car is not close to me so i cant look at it and compare it to my 66 that i...

Still looking for a 66 Cuda Driver side rear quarter panel. William

Need advice i bought a spot blaster / vac combo. What would be the best media to use in. I would like to take the car down to bare metal and have herd that sand can sometimes warp the metal. Best way to remove quarter panel trim or and pointers please. It on a 66 Cuda. Thank you for...

I have a 66 Cuda and I’m in the middle of tearing out the interior so I can redo it. I have limited space so and have to move the car in and out of the garage to work on it. I need to know what I need to do to remove the dash but be able to start the car so I can move it in and out again...

Advice Pleas on rear end. Ok first some info on the car I have. It a 1966 Plymouth barracuda that one of the previous owners has put in a 318 with 360 heads and edelbrock 316-360 intake with a 600cfm carburetor. I had to take apart the top end and replace all the gaskets and rebuild the...

Need floor pans and Driver side quarter panel William

Trying to get a 66 Cuda that i just got to run and having trouble finding our what engine it is. The heads are mark 3769974 which by what i find are 360 1975-1976 I do not see any numbers on the block.. Is there any other way to tell without having to pull the engine out? The maifold...

I just started working on my recent purchase a 66 cuda and have a few things that i need help with. 1- Map light, I found it under the glove box if someone can show me a pic of where it goes or any info on it. 2- Glove Box Light. Found the wires but it has been cut off. A pic of what I...

Removing my Fuel gauge this clip snapped in half. (See pic) 1- Do i need it? 2- Can i just use one of the nuts like the other post? Found this pic on the site to show what clip broke in half

I just picked up a 1966 Barracuda that has the 273 with edelbrock manifold and 4 barrel carb. I have no spark at the plug wires and started looking around and found 2 wires that come out of the distributor (Red and Black) the black wire goes to the NEG side of the coil but the RED wire is...

Found this and got a good deal (I Hope) I paid $3,000 Will

Looking for a Driver rear 1966 Barracuda Quarter Panel or at least the 1/3 rear around the tail light. Thank you for your time