Search results for query: *

All right gentlemen. I am in need of some help to find what parts are needed for my transmission rebuild. My car is a drag car only, It weighs 2750 race ready. It has a 360 with a MP528 cam putting out maybe 400hp if I'm lucky. I am going to put in a Griner transbrake. What other parts are...

i will take it for full asking price. so put me in line to buy thanks.

38dodge pm sent. I had something very important come up. Life happens.

Sold thanks fabo

sorry for the confusion and thanks for the correction.

here you go

I will double check the demensions and get back to you tomorrow.

i have a set of motor mounts out of a 67 340 barracuda. $25 + shipping

I have a small block 4 speed bell housing out of an 85 w250. $75 plus shipping from 96007

can you tell me what shipping would be for the dash frame to 96007

I could not find any casting numbers on my heads for this motor, except for when I looked under the heads. the 915 J heads that are on my drag car were easy to see.

ok guys, i found it. I had to take off my intake manifold and turn the engine on my stand, and I found the casting numbers underneath the head. the numbers are 4343475-A. can any one tell me the specs for these heads. Im guesing its 1.88 int. 1.60 exh. and a combustion chamber of 70 +/- 2 which...

Hey guys, can any one tell me where I can find the head identification numbers for the heads that are on my 360. I just pulled it out of an 86 w250 4x4. the block has 4179930-360-2 on it. I pulled the valve covers off, the only numbers I could see was 274. I did see the numbers 00599 9293 1 242...

I went through the same thing with my wife. I am very passionate about competing in 3d archery. But I got tired of her relentless bitching so I cut back on my practicing a lot "I pretty much don't shoot any more". So then because I am the type of guy that has to have a hobby I played in a pool...

Pse diablo, pse xforce 300's with a 3 blade 100 grain muzzy. My rifle is a sporterized mosin negant.

Ok will do thanks.

All right. I am in need of some recommendations for the jet sizes I should use in my barrowed 750hp. My cars specs are: 1975 dart sport 360 la stock stroke and unknown bore w/ about 10:1 compression 360 j heads with 2.08" intake and 1.60" exhaust valves MP .528 cam Eddy performer...

I like the white top

I thought Stacey left trucks back in the day because he/they put long hours and lots of big money parts into a really nice truck and because all the parts that was used were sponsore donated. so they had to crush the truckafter it was completed. He wasn't cool with that so he left. Correct me if...

now what if someone had 50psi at 1000rpm and 70psi at 3500rpm. Is that bad

pending payment

Send me a pic and some info like what it was on and the current jetting please

Clutch

8 3/4" third member 489 case with 3.55 sure grip. $400 Plus shipping. Or trade for Holley 750dp-950dp race carb. Or trade for line lock system and 904 manual valve body. I will post a pic soon.

I am using the same flex plate that is on the motor in your picture. For the 904 I had to use the inside bolt holes for torque converter. So yes. That flex plate was just a little to big to allow the starter to engage the converter. The starter bolted up fine. The problem was the bearing behind...

The starter will have a small bracket that bolts on the battery post and relay post. If you take that bracket off make sure your relay post is secured by itself. On the one I got the bracket used the battery post to secure the relay post. I didn't know that so I took it off. When I tried to bolt...

I just had the same problem. The motor I put in my car had a SB 727. I am using a 999. I was able to marry the trans and engine and bolt the flex plate no problem. Once I put in the factory starter I found that the bearing backing the drive gear was hitting the flex plate by about 1/8". I went...

I will put on fiberglass bumpers and brackets. as well as a fiberglass fron valance, and trunk lid. but that is after I have reced it for half the season.

no the doors are completely fiberglass

when I put in a manual valve body. I will put a shift light on top of my dash.